If ρ is the density and η is coefficient of viscosity of fluid which flows with a speed v in the pipe of diameter d, the correct formula for Reynolds number Re is:
\(R_e\) = \(\frac{ηd }{ρν}\)
\(R_e\) = \(\frac{ρν}{ηd}\)
\(R_e\) = \(\frac{ρνd}{η}\)
\(R_e\) = \(\frac{η}{ρνd}\)
The Correct Option is C
Solution and Explanation
The correct answer is (C) : \(R_e\) = \(\frac{ρνd}{η}\)
\(R_e\) = \(\frac{ ρνd}{η }\)
Direct formula based.
Top Questions on Viscosity
In an experiment to determine the figure of merit of a galvanometer by half deflection method, a student constructed the following circuit. He applied a resistance of \( 520 \, \Omega \) in \( R \). When \( K_1 \) is closed and \( K_2 \) is open, the deflection observed in the galvanometer is 20 div. When \( K_1 \) is also closed and a resistance of \( 90 \, \Omega \) is removed in \( S \), the deflection becomes 13 div. The resistance of galvanometer is nearly:
- KCET - 2025
- Physics
- Viscosity
- The diameter of spherical galena particles that have the same settling velocity as spherical quartz particles of diameter 25 μm (both settling in water) is ............. μm (rounded off to one decimal place). Assume Stokes law of settling to be valid. Given: Density of galena = 7400 kg m$^{-3}$, density of quartz = 2600 kg m$^{-3}$, density of water = 1000 kg m$^{-3}$.
- For an application where the Reynolds number is to be kept constant, a liquid with density of 1 g per cubic cm and viscosity of 0.01 Poise results in a characteristic speed of 1 cm per second. If this liquid is replaced by another with density of 1.25 g per cubic cm and viscosity of 0.015 Poise, the characteristic velocity will be ........... cm per second (rounded off to one decimal place). Assume the characteristic length of the flow to be the same in both cases.
- Consider a fully developed, steady, one-dimensional, laminar flow of a Newtonian liquid through a pipe. The maximum velocity in the pipe is proportional to which of the following quantities? Given: Delta P is the difference between the outlet and inlet pressure, mu is the dynamic viscosity of the liquid, and R and L are radius and length of the pipe, respectively.
- At high temperatures, which one of the following empirical expressions correctly describes the variation of dynamic viscosity \(\mu\) of a Newtonian liquid with absolute temperature \(T\)? (Given: \(A\) and \(B\) are positive constants.)
Questions Asked in JEE Main exam
- If the equation of the parabola with vertex $\left(\frac{3}{2},\, 3\right)$ and the directrix $x + 2y = 0$ is
$$ ax^2 + by^2 - cxy - 30x - 60y + 225 = 0, $$ then $\alpha + \beta + \gamma$ is equal to:- JEE Main - 2025
- Calculus
- In a first order decomposition reaction, the time taken for the decomposition of reactant to one fourth and one eighth of its initial concentration are $ t_1 $ and $ t_2 $ (s), respectively. The ratio $ t_1 / t_2 $ will be:
- JEE Main - 2025
- Chemical Kinetics
- HA $ (aq) \rightleftharpoons H^+ (aq) + A^- (aq) $ The freezing point depression of a 0.1 m aqueous solution of a monobasic weak acid HA is 0.20 °C. The dissociation constant for the acid is Given: $ K_f(H_2O) = 1.8 \, \text{K kg mol}^{-1} $, molality ≡ molarity
- JEE Main - 2025
- Colligative Properties
20 mL of sodium iodide solution gave 4.74 g silver iodide when treated with excess of silver nitrate solution. The molarity of the sodium iodide solution is _____ M. (Nearest Integer value) (Given : Na = 23, I = 127, Ag = 108, N = 14, O = 16 g mol$^{-1}$)
- JEE Main - 2025
- Stoichiometry and Stoichiometric Calculations
- Which of the following binary mixture does not show the behavior of minimum boiling azeotropes?
- JEE Main - 2025
- Solutions
Concepts Used:
Viscosity
Viscosity is a measure of a fluid’s resistance to flow. The SI unit of viscosity is poiseiulle (PI). Its other units are newton-second per square metre (N s m-2) or pascal-second (Pa s.) The dimensional formula of viscosity is [ML-1T-1].
Viscosity: Formula
Viscosity is measured in terms of a ratio of shearing stress to the velocity gradient in a fluid. If a sphere is dropped into a fluid, the viscosity can be determined using the following formula:
η = [2ga2(Δρ)] / 9v
Where ∆ρ is the density difference between fluid and sphere tested, a is the radius of the sphere, g is the acceleration due to gravity and v is the velocity of the sphere.
Viscosity: Types
- Dynamic viscosity: When the viscosity is measured directly by measuring force. It is defined as the ratio of shear stress to the shear strain of the motion. Dynamic viscosity is used to calculate the rate of flow in liquid.
- Kinematic viscosity: There is no force involved. It can be referred to as the ratio between the dynamic viscosity and density of the fluid. It can be computed by dividing the dynamic viscosity of the fluid with fluid mass density.
- Laminar flow: Laminar flow is the type of flow in which the fluid moves smoothly or in a regular path from one layer to the next. Laminar flow occurs in lower velocities.