An aluminium wire is stretched to make its length, 0.4% larger. The percentage change in resistance is
- 0.4%
- 0.2%
- 0.8%
- 0.6%
The Correct Option is C
Solution and Explanation
When the wire is stretched, volume remains constant. If length is increased by 0.4% area will decrease by 0.4%.
From, \(R=\frac {ρI}{A}\)
\(\frac {dR}{R}\times 100=\frac {dI}{I}\times100+\frac {dA}{A}\times 100\)
The percentage change in resistance,
%\(R\) =\( 0.4 + 0.4\)
%\(R\)= \(0.8\)%
So, the correct option is (C): \(0.8\)%
Top Questions on Resistance
A wire of resistance $ R $ is bent into a triangular pyramid as shown in the figure, with each segment having the same length. The resistance between points $ A $ and $ B $ is $ \frac{R}{n} $. The value of $ n $ is:
- JEE Main - 2025
- Physics
- Resistance
- A coil of resistance 10 \( \Omega \) is connected to a battery of 12 V. If the current flowing through the coil is 2 A, what is the power dissipated in the coil?
- BITSAT - 2025
- Physics
- Resistance
- What is the resistance of a conductor if the potential difference across it is 12 V and the current flowing through it is 3 A?
- VITEEE - 2025
- Physics
- Resistance
- A resistor of resistance $ 10\, \Omega $ is connected across a $ 20\, V $ battery. Calculate the current flowing through the resistor.
- BITSAT - 2025
- Physics
- Resistance
- Find the effective resistance of the network of resistors between points A and F as shown in the figure.
Questions Asked in JEE Main exam
A conducting bar moves on two conducting rails as shown in the figure. A constant magnetic field \( B \) exists into the page. The bar starts to move from the vertex at time \( t = 0 \) with a constant velocity. If the induced EMF is \( E \propto t^n \), then the value of \( n \) is _____.
- JEE Main - 2025
- Magnetic Field
- Concentrated nitric acid is labelled as 75%by mass. The volume in mL of the solution which contains 30 g of nitric acid is: Given: Density of nitric acid solution is 1.25 g/mL.
- JEE Main - 2025
- Solutions
- A physical quantity \( Q \) is related to four observables \( a \), \( b \), \( c \), and \( d \) as follows: \[ Q = \frac{a b^4}{c d^2} \] Where:
- \( a = (60 \pm 3) \, \text{Pa} \),
- \( b = (20 \pm 0.1) \, \text{m} \),
- \( c = (40 \pm 0.2) \, \text{N·s/m}^2 \),
- \( d = (50 \pm 0.1) \, \text{m} \).
Then the percentage error in \( Q \) is:- JEE Main - 2025
- Error analysis
- Let circle $C$ be the image of
$$ x^2 + y^2 - 2x + 4y - 4 = 0 $$
in the line
$$ 2x - 3y + 5 = 0 $$
and $A$ be the point on $C$ such that $OA$ is parallel to the x-axis and $A$ lies on the right-hand side of the centre $O$ of $C$.
If $B(\alpha, \beta)$, with $\beta < 4$, lies on $C$ such that the length of the arc $AB$ is $\frac{1}{6}$ of the perimeter of $C$, then $\beta - \sqrt{3}\alpha$ is equal to: - Assume a living cell with 0.9%(\(w/w\)) of glucose solution (aqueous). This cell is immersed in another solution having equal mole fraction of glucose and water. (Consider the data up to first decimal place only) The cell will:
- JEE Main - 2025
- osmosis
Concepts Used:
Resistance
Resistance is the measure of opposition applied by any object to the flow of electric current. A resistor is an electronic constituent that is used in the circuit with the purpose of offering that specific amount of resistance.
R=V/I
In this case,
v = Voltage across its ends
I = Current flowing through it
All materials resist current flow to some degree. They fall into one of two broad categories:
- Conductors: Materials that offer very little resistance where electrons can move easily. Examples: silver, copper, gold and aluminum.
- Insulators: Materials that present high resistance and restrict the flow of electrons. Examples: Rubber, paper, glass, wood and plastic.
Resistance measurements are normally taken to indicate the condition of a component or a circuit.
- The higher the resistance, the lower the current flow. If abnormally high, one possible cause (among many) could be damaged conductors due to burning or corrosion. All conductors give off some degree of heat, so overheating is an issue often associated with resistance.
- The lower the resistance, the higher the current flow. Possible causes: insulators damaged by moisture or overheating.