Question:
A company purchased two machines, Machine A and Machine B, at the same time. The purchase price, estimated useful life and the estimated salvage value of the two machines are given in the table. Machine A Machine B Purchase price INR 20,000 INR 15,000 Estimated useful life 10 years 20 years Estimated salvage value INR 5,000 INR 5,000
Using the straight-line depreciation method for both the machines, the difference (in INR) between the value of Machine A and the value of Machine B at the end of five years is _____ . (Answer in integer)
A company purchased two machines, Machine A and Machine B, at the same time. The purchase price, estimated useful life and the estimated salvage value of the two machines are given in the table.
Using the straight-line depreciation method for both the machines, the difference (in INR) between the value of Machine A and the value of Machine B at the end of five years is _____ . (Answer in integer)
| Machine A | Machine B | |
|---|---|---|
| Purchase price | INR 20,000 | INR 15,000 |
| Estimated useful life | 10 years | 20 years |
| Estimated salvage value | INR 5,000 | INR 5,000 |
Updated On: Feb 10, 2025
Hide Solution
Verified By Collegedunia
Correct Answer: 0
Solution and Explanation
The answer is 0.
Was this answer helpful?
0
2
Top Questions on Project Management
- Which one of the following is the excess of variable time over the activity time when all jobs start as early as possible?
- AP PGECET - 2024
- Mechanical Engineering
- Project Management
Consider the network diagram shown in Figure. The time estimates in days along the arrows represents the activities. The project completion time in days based on critical path is
- AP PGECET - 2024
- Mechanical Engineering
- Project Management
- What will be the expected time for driving the precast piles for a bridge abutment activity having optimistic time 22, most likely time 30, and pessimistic time 50?
- CUET (PG) - 2024
- Water Engineering and Management
- Project Management
- Five jobs A, B, C, D and E are available at time t = 0 for processing at a machine, and their processing times are listed.If the jobs are processed using the shortest processing time (SPT) rule, the average flow time (in days) is _____ . (Rounded off to 1 decimal place)
Job A B C D E Processing time (in days) 9 6 4 5 8 - GATE PI - 2024
- Operations Research and Operations Management
- Project Management
- Which one of the following is not true about Total Productive Maintenance (TPM)?
- GATE PI - 2024
- Industrial Engineering
- Project Management
View More Questions
Questions Asked in GATE PI exam
- The left-hand side of a 20 cm thick wall is maintained at 25°C. The right-hand side of the wall is exposed to hot air at 50°C. There is no heat generation inside the wall and its thermal conductivity is 100 W/m·K. The convective heat transfer coefficient is 50 W/m²·K. Under steady state condition, the temperature (in °C) of the right-hand side surface of the wall is ........ (Rounded off to one decimal place).
- GATE PI - 2025
- Heat Transfer and Associated Losses
- Water flows through a smooth circular pipe of diameter 10 cm and length 10 m. The pressure drop across the length of the pipe is 0.2 Pa. Kinematic viscosity and density of water are \(1 \times 10^{-6} \, {m}^2/{s}\) and 1000 \({kg/m}^3\), respectively. Assuming laminar and fully developed flow throughout the pipe, the velocity of water (in mm/s) at the center of the pipe is ........ (Rounded off to one decimal place)
- GATE PI - 2025
- Fluid Mechanics
The table shows the data of running a machine for five years. The original machine cost is Rupees 70,000. In order to minimize the average total cost per year for running the machine, the machine should be replaced after ............. years. (Answer in integer)
- GATE PI - 2025
- Economic Activities
- The zero line of the Vernier scale lies between divisions 20 and 21 of the main scale. The 4th Vernier scale division exactly coincides with a main scale division. The 5 divisions of the Vernier scale are equal to 4 divisions of the main scale. If one main scale division is 1 mm, the measured value (in mm) is ........... (Rounded off to one decimal place)
- GATE PI - 2025
- Industrial and Production
A company purchases items in bulk for getting quantity discounts in the item’s price. The price break-up is given in the table. The annual demand for the item is 5000 units. The ordering cost is Rupees 400 per order. The annual inventory carrying cost is 30 percent of the purchase price per unit. The optimal order size (in units) is .......... (Answer in integer)
- GATE PI - 2025
- Industrial and Production
View More Questions