List of top Electronics Engineering Questions asked in CUET (PG)

In binary data transmission, DPSK is preferred over PSK because
The Nyquist plot and step response/transfer function is given. Match List-I (Nyquist plot) with List-II (corresponding step response/transfer function).
The damping ratio and undamped natural frequency of a closed loop system as shown in the figure, are denoted as \(\zeta\) and \(\omega_n\) respectively. The value of \(\zeta\) and \(\omega_n\) are:
(A) \(\zeta = 0.5\)
(B) \(\zeta = 0.707\)
(C) \(\omega_n = 10\) rad/s
(D) \(\omega_n = 100\) rad/s
Choose the correct answer from the options given below:
Choose the correct statements from the following
A. The lag-compensation has a pole nearer to the origin.
B. The lag-compensation has a zero nearer to the origin.
C. The lag-compensator decreases the bandwidth.
D. The lag-compensator increases the bandwidth.
A second order control system has a damping ratio \(\zeta = 0.8\) and the natural frequency of oscillation \(\omega_n = 12\) rad/sec. Determine the damped frequency of oscillation.
Bounded-input bounded-output stability implies asymptotic stability for
A. Completely controllable system
B. Completely observable system
C. Uncontrollable system
D. Unobservable system
Which of the above statements is/are correct?
Choose the correct answer from the options given below:
Which one of the following statements regarding the effect of the phase lead network is not correct?
The value of the steady state error for first order system, \(\frac{1}{sT+1}\) with Unit Ramp Function will be
In the root locus plot, the breakaway points
A. Need not always be on the real axis alone.
B. Must lie on the root loci.
C. Must lie between 0 and -1.
Choose the correct answer from the options given below:
The Boolean function f implemented in the figure using two input multiplexers is
It is desired to multiply the numbers 0AH by 0BH and store the result in the accumulator. The numbers are available in registers B and C, respectively. A part of the 8085 program for this purpose is given below: MVI A, 00H; Loop:---; ---; ---; ---. The sequence of remaining 4 instructions to complete the program would be
The maximum clock frequency in MHz of a 4-stage ripple counter, utilizing flip-flops, with each flip-flop having a propagation delay of 20 ns, is

A MOD 2 and a MOD 5 up-counter when cascaded together results in a MOD ______ counter.

Neglecting the delays due to the logic gates in the circuit shown in the figure, the decimal equivalent of the binary sequence [ABCD] of initial logic states, which will not change with the clock, is
An 8-bit ADC converts analog voltage in the range of 0 to +5 V to the corresponding digital code as per the conversion characteristics shown in the figure. For \(V_{in}\) = 1.9922 volt, which of the following digital output, given in hex, is true?
In the astable multivibrator circuit shown in the figure, the frequency of oscillation at the output is
The internal blocks in the Voltage-controlled-Oscillator (VCO) IC-566 are given below.
A. Current Sources,
B. Buffer Amplifier,
C. Schmitt Trigger,
D. Modulation Input.
Choose the correct sequence (input towards output) of internal blocks of VCO from the options given below from input side to output side:
The circuit in the given figure is,
The circuit name (List-I) and their circuit diagram (List-II) are given in the table below. Match List-I with List-II.
}
The circuit shown in the figure, the forward voltage of the diode is 0.7 V and its dynamic resistance is 2 \(\Omega\). The current through the 20 \(\Omega\) resistor is
A circuit which resonates at 1 MHz has a Q of 10. Bandwidth between half-power points is
Negative feedback in amplifiers A. improves the signal-to-noise ratio at the input. B. improves the signal-to-noise ratio at the output. C. does not affect the signal-to-noise ratio at the output. D. reduces distortion. Choose the correct answer from the options given below:
The early-effect in a BJT is caused by
If fixed positive charges are present in the gate oxide of an n-channel enhancement type MOSFET, it will lead to
The following circuit employing pass transistor logic, all NMOS transistors are identical with a threshold voltage of 1 V. Ignoring the body-effect, the output voltages at P, Q and R are,