Question:
Tmin=300 K,Tmax=1200K,Q=1200 KJ.Find work done.
Tmin=300 K,Tmax=1200K,Q=1200 KJ.Find work done.
Updated On: Aug 9, 2024
Hide Solution
Verified By Collegedunia
Correct Answer: 900
Solution and Explanation
The correct answer is 900 KJ.
Was this answer helpful?
0
0
Top Questions on Calculation of work and heat in various processes
- Consider a slab of 20mm thickness. There is a uniform heat generation of \(\dot{q}\) = 100MW/m3 inside the slab. The left and right faces of the slab are maintained at 150°C and 110°C, respectively. The plate has a constant thermal conductivity of 200W/(m.K). Considering a 1-D steady state heat conduction, the location of the maximum temperature from the left face will be at (answer in integer).
- GATE Metallurgy - 2024
- Fluid Mechanics and Thermal Sciences
- Calculation of work and heat in various processes
- A condenser is used as a heat exchanger in a large steam power plant in which steam is condensed to liquid water. The condenser is a shell and tube heat exchanger which consists of 1 shell and 20,000 tubes. Water flows through each of the tubes at a rate of 1kg/s with an inlet temperature of 30°C. The steam in the condenser shell condenses at the rate of 430kg/s at a temperature of 50°C. If the heat of vaporization is 2.326MJ/kg and specific heat of water is 4kJ/(kg.K), the effectiveness of the heat exchanger is _____ (rounded off to 3 decimal places).
- GATE Metallurgy - 2024
- Fluid Mechanics and Thermal Sciences
- Calculation of work and heat in various processes
find total heat- GATE Metallurgy
- Fluid Mechanics and Thermal Sciences
- Calculation of work and heat in various processes
Questions Asked in GATE Metallurgy exam
- A ram in the form of a rectangular body of size l=9m and b=2m is suspended by two parallel ropes of lengths 7m. Assume the center-of-mass of the body is at its geometric center and g = 9.81m/s2. For striking the object P with a horizontal velocity of 5m/s, what is the angle θ with the vertical from which the ram should be released from rest?
- GATE Metallurgy - 2024
- Forces on submerged bodies
- If the value of the double integral
\(\displaystyle\int^{4}_{x=3}\displaystyle\int^{2}_{y=1}\frac{dydx}{(x+y)^2}\)
is \(\log e (\frac{a}{24})\), then a is ____ (answer in integer).- GATE Metallurgy - 2024
- Integration by trapezoidal and Simpson’s rules
- If x(t) satisfies the differential equation
\(t\frac{dx}{dt}+(t-x)=0\)
subject to the condition x(1) = 0, then the value of x(2) is_____(rounded off to 2 decimal places).- GATE Metallurgy - 2024
- Higher order linear ODEs with constant coefficients
- The value of the surface integral
\(\displaystyle\oiint_{s}zdxdy\)
where S is the external surface of the sphere x2 + y2 + z2 = R2 is- GATE Metallurgy - 2024
- Vector identities
- A heat pump (H.P.) is driven by the work output of a heat engine (H.E.) as shown in the figure. The heat engine extracts 150 kJ of heat from the source at 1000 K. The heat pump absorbs heat from the ambient at 280 K and delivers heat to the room which is maintained at 300 K. Considering the combined system to be ideal, the total amount of heat delivered to the room together by the heat engine and heat pump is _____kJ (answer in integer).
- GATE Metallurgy - 2024
- I.C. Engines
View More Questions