Question:
A solid massless cylindrical member of 50 mm diameter is rigidly attached at one end, and is subjected to an axial force, P = 100 kN and torque T = 600 Nm at the other end as shown. Assume that the axis of the cylinder is normal to the support. considering distortion energy theory with allowable yield stress as 300 MPa. The factor of safety in the design is _____ (Round of one decimal place)
A solid massless cylindrical member of 50 mm diameter is rigidly attached at one end, and is subjected to an axial force, P = 100 kN and torque T = 600 Nm at the other end as shown. Assume that the axis of the cylinder is normal to the support. considering distortion energy theory with allowable yield stress as 300 MPa. The factor of safety in the design is _____ (Round of one decimal place)
Updated On: Oct 29, 2024
Hide Solution
Verified By Collegedunia
Correct Answer: 4
Solution and Explanation
The correct answer is 4.
Was this answer helpful?
1
1
Top Questions on Failure theories
- Modified Tsai-Hill theory
- TANCET - 2024
- Aeronautical and Aerospace Engineering
- Failure theories
- Which one of the following failure theories in the most conservative design approach against fatigue failure
- GATE Metallurgy - 2024
- Applied Mechanics and Design
- Failure theories
- A structural member under loading has a uniform state of plane stress which in usual notations is given by $\sigma_x = 3P$, $\sigma_y = -2P$ and $\tau_{xy} = \sqrt{2}\,P$, where $P>0$. The yield strength of the material is 350 MPa. If the member is designed using the maximum distortion energy theory, then the value of $P$ at which yielding starts (according to the maximum distortion energy theory) is
- GATE ME - 2022
- Applied Mechanics and Design
- Failure theories
Uniaxial tension test (see the figure) is conducted on two different samples prepared with homogeneous, isotropic materials. One of the materials is brittle, whereas the other is ductile.
Assuming that there is no stress concentration at loading points, the failurewould initiate:
- GATE AE - 2021
- Structures
- Failure theories
- The von Mises stress at a point in a body subjected to forces is proportional to the square root of the
- GATE ME - 2021
- Applied Mechanics and Design
- Failure theories
Questions Asked in GATE Metallurgy exam
- At the instant when OP is vertical and AP is horizontal, the link OD is rotating counter clockwise at a constant rate w=7rad/s. Pin P on link OD slides in the slot BC of link ABC which is hinged at A, and causes a clockwise rotation of the link ABC. The magnitude of angular velocity of link ABC for this instant is _____rad/s (rounded off to 2 decimal places).
- GATE Metallurgy - 2024
- Principles of the design of machine elements such as bolted, riveted and welded joints
- In an arc welding process, the voltage and current are 30V and 200A, respectively. The cross-sectional area of the joint is 20 mm2 and the welding speed is 5mm/s. The heat required to melt the material is 20 J/s. The percentage of heat lost to the surrounding during the welding process is ____(rounded off to 2 decimal places).
- GATE Metallurgy - 2024
- Principles of welding, brazing, soldering and adhesive bonding
- Let f(z) be an analytic function, where z = x + iy. If the real part of f(z) is cosh x cos y, and the imaginary part of f(z) is zero for y = 0, then f(z) is
- GATE Metallurgy - 2024
- Analytic functions
- Steady, compressible flow of air takes place through an adiabatic converging- diverging nozzle, as shown in the figure. For a particular value of pressure difference across the nozzle, a stationary normal shock wave forms in the diverging section of the nozzle. If E and F denote the flow conditions just upstream and downstream of the normal shock, respectively, which of the following statement(s) is/are TRUE?
- GATE Metallurgy - 2024
- Basics of compressible fluid flow
- A set of jobs U, V, W, X, Y, Z arrive at time t = 0 to a production line consisting of two workstations in series. Each job must be processed by both workstations in sequence (i.e., the first followed by the second). The process times (in minutes) for each job on each workstation in the production line are given below.
Job U V W X Y Z Workstation 1 5 7 3 4 6 8 Workstation 2 4 6 6 8 5 7
The sequence in which the jobs must be processed by the production line if the total makespan of production is to be minimized is- GATE Metallurgy - 2024
- Principles of non-traditional machining processes
View More Questions