Question:
Consider a slab of 20mm thickness. There is a uniform heat generation of \(\dot{q}\) = 100MW/m3 inside the slab. The left and right faces of the slab are maintained at 150°C and 110°C, respectively. The plate has a constant thermal conductivity of 200W/(m.K). Considering a 1-D steady state heat conduction, the location of the maximum temperature from the left face will be at (answer in integer).
Consider a slab of 20mm thickness. There is a uniform heat generation of \(\dot{q}\) = 100MW/m3 inside the slab. The left and right faces of the slab are maintained at 150°C and 110°C, respectively. The plate has a constant thermal conductivity of 200W/(m.K). Considering a 1-D steady state heat conduction, the location of the maximum temperature from the left face will be at (answer in integer).
Updated On: Jul 9, 2024
Hide Solution
Verified By Collegedunia
Correct Answer: 6
Solution and Explanation
The correct answer is:6 to 6
Was this answer helpful?
0
0
Top Questions on Calculation of work and heat in various processes
- A condenser is used as a heat exchanger in a large steam power plant in which steam is condensed to liquid water. The condenser is a shell and tube heat exchanger which consists of 1 shell and 20,000 tubes. Water flows through each of the tubes at a rate of 1kg/s with an inlet temperature of 30°C. The steam in the condenser shell condenses at the rate of 430kg/s at a temperature of 50°C. If the heat of vaporization is 2.326MJ/kg and specific heat of water is 4kJ/(kg.K), the effectiveness of the heat exchanger is _____ (rounded off to 3 decimal places).
- GATE Metallurgy - 2024
- Fluid Mechanics and Thermal Sciences
- Calculation of work and heat in various processes
- Tmin=300 K,Tmax=1200K,Q=1200 KJ.Find work done.
- GATE Metallurgy
- Fluid Mechanics and Thermal Sciences
- Calculation of work and heat in various processes
find total heat- GATE Metallurgy
- Fluid Mechanics and Thermal Sciences
- Calculation of work and heat in various processes
Questions Asked in GATE Metallurgy exam
- Let f(z) be an analytic function, where z = x + iy. If the real part of f(z) is cosh x cos y, and the imaginary part of f(z) is zero for y = 0, then f(z) is
- GATE Metallurgy - 2024
- Analytic functions
- Steady, compressible flow of air takes place through an adiabatic converging- diverging nozzle, as shown in the figure. For a particular value of pressure difference across the nozzle, a stationary normal shock wave forms in the diverging section of the nozzle. If E and F denote the flow conditions just upstream and downstream of the normal shock, respectively, which of the following statement(s) is/are TRUE?
- GATE Metallurgy - 2024
- Basics of compressible fluid flow
- In an arc welding process, the voltage and current are 30V and 200A, respectively. The cross-sectional area of the joint is 20 mm2 and the welding speed is 5mm/s. The heat required to melt the material is 20 J/s. The percentage of heat lost to the surrounding during the welding process is ____(rounded off to 2 decimal places).
- GATE Metallurgy - 2024
- Principles of welding, brazing, soldering and adhesive bonding
- A set of jobs U, V, W, X, Y, Z arrive at time t = 0 to a production line consisting of two workstations in series. Each job must be processed by both workstations in sequence (i.e., the first followed by the second). The process times (in minutes) for each job on each workstation in the production line are given below.
Job U V W X Y Z Workstation 1 5 7 3 4 6 8 Workstation 2 4 6 6 8 5 7
The sequence in which the jobs must be processed by the production line if the total makespan of production is to be minimized is- GATE Metallurgy - 2024
- Principles of non-traditional machining processes
- A ram in the form of a rectangular body of size l=9m and b=2m is suspended by two parallel ropes of lengths 7m. Assume the center-of-mass of the body is at its geometric center and g = 9.81m/s2. For striking the object P with a horizontal velocity of 5m/s, what is the angle θ with the vertical from which the ram should be released from rest?
- GATE Metallurgy - 2024
- Forces on submerged bodies
View More Questions