Terylene polymer is obtained by condensation of :
- Ethane-1, 2-diol and Benzene-1, 3 dicarboxylic acid
- Propane-1, 2-diol and Benzene-1, 4 dicarboxylic acid
- Ethane-1, 2-diol and Benzene-1, 4 dicarboxylic acid
- Ethane-1, 2-diol and Benzene-1, 2 dicarboxylic acid
The Correct Option is C
Solution and Explanation
Terylene polymer is obtained by condensation of : Ethane-1, 2-diol and Benzene-1, 4 dicarboxylic acid
Therefore, the correct option is (C): Ethane-1, 2-diol and Benzene-1, 4 dicarboxylic acid
Top Questions on Polymers
- A polymer melt being extruded through a spinneret hole of circular cross-section exhibits a die-swell ratio of 2.2. The extrusion velocity and volumetric flow rate during this extrusion process are 20 m/min and \(2.6 \times 10^{-8}\) m\(^3\)/s, respectively. The maximum diameter (mm) of the extruded melt after exit from the spinneret hole (rounded off to 2 decimal places) is:
- The main constituent of vinegar is:
- The monomer of natural rubber is:
- The catalyst used in the preparation of high density polythene is
- Arrange the following polymers in increasing order of intermolecular forces:
Questions Asked in JEE Main exam
Two circular discs of radius \(10\) cm each are joined at their centres by a rod, as shown in the figure. The length of the rod is \(30\) cm and its mass is \(600\) g. The mass of each disc is also \(600\) g. If the applied torque between the two discs is \(43\times10^{-7}\) dyne·cm, then the angular acceleration of the system about the given axis \(AB\) is ________ rad s\(^{-2}\).
- JEE Main - 2026
- Rotational motion
- If \[ \frac{\tan(A-B)}{\tan A}+\frac{\sin^2 C}{\sin^2 A}=1, \quad A,B,C\in\left(0,\frac{\pi}{2}\right), \] then:
- JEE Main - 2026
- Trigonometry
Match the LIST-I with LIST-II for an isothermal process of an ideal gas system.
Choose the correct answer from the options given below:
- JEE Main - 2026
- Thermodynamics and Work Done
- A bag contains 10 balls out of which \( k \) are red and \( (10-k) \) are black, where \( 0 \le k \le 10 \). If three balls are drawn at random without replacement and all of them are found to be black, then the probability that the bag contains 1 red and 9 black balls is:
- JEE Main - 2026
- Probability
Which one of the following graphs accurately represents the plot of partial pressure of CS₂ vs its mole fraction in a mixture of acetone and CS₂ at constant temperature?
- JEE Main - 2026
- Organic Chemistry
Concepts Used:
Types of Polymerization Reactions
Polymerization is a chemical reaction in which a large number of monomer molecules combine to produce a polymer. A polymerization can yield macromolecules with a linear or branching structure. They can also take the form of a three-dimensional complicated network.
Types of Polymerisation
Polymerization reactions are divided into two groups, namely, Addition polymerization (chain reaction) and condensation reaction (step reaction).
- Addition Polymerisation: As the name denotes, we can see the addition of monomers to form a polymer, twice the number or even more than that. Here, we can either select monomers of the same species or of different species. When we choose the single species monomers for the polymerization, the product thus formed is known as homopolymer (for example polythene used to make bags). When we use two different species for additional polymerization, the polymer would be known as copolymer (for example, Buna-S and Buna-N).
- Condensation Polymerisation: In the condensation polymerisation, we can find elimination of compounds like HCL, water, alcohol etc...; while the monomers condense during the reaction process. This reaction happens between tri-function and bi-function monomer units and results in the formation of polymers like nylon.