Question:
In a forming operation, the plastic deformation of a steel specimen starts under plane stress condition, where the principal stresses are \(σ_1=200\ Mpa\) and \(σ_2 = 100\ Mpa\). If the steel specimen follows von-Mises yield criterion, then the uniaxial tensile yield strength (in Mpa) of this steel material is ____ . (Rounded off to 1 decimal place)
In a forming operation, the plastic deformation of a steel specimen starts under plane stress condition, where the principal stresses are \(σ_1=200\ Mpa\) and \(σ_2 = 100\ Mpa\). If the steel specimen follows von-Mises yield criterion, then the uniaxial tensile yield strength (in Mpa) of this steel material is ____ . (Rounded off to 1 decimal place)
Updated On: Jul 12, 2024
- 173.2
- 200.0
- 100.0
- 223.6
Hide Solution
Verified By Collegedunia
The Correct Option is A
Solution and Explanation
The correct option is (A): 173.2
Was this answer helpful?
0
0
Top Questions on Maximum Shear Stress Theory
- For a mild steel specimen subjected to uniaxial tensile load, which of the following is/are TRUE?
- GATE PI - 2024
- Strength of Materials
- Maximum Shear Stress Theory
- A cantilever beam of T cross-section carries uniformly distributed load. Where does the maximum magnitude of the bending stress occur?
- CUET (PG) - 2023
- Water Resources Engineering
- Maximum Shear Stress Theory
- In a direct shear test, the shear strength and normal stress on a dry sand sample at failure are 0.6 kg/cm2 and 10 kg/cm2, respectively. The angle of internal friction of the sand will be nearly
- CUET (PG) - 2023
- Water Resources Engineering
- Maximum Shear Stress Theory
- Given below are two statements:
Statement - I: Rate of change of shear force (f) at any section of a loaded beam is equal to the Rate of Loading (w) at the section i.e. \(w=\frac{df}{dx}\)
Statement - II: Rate of change of bending moment at any section of a loaded beam represent the shear force (F) at the section is \(f=\frac{dm}{dx}.\)
In the light of the above statements, choose the correct answer from the options given below :- CUET (PG) - 2023
- Water Resources Engineering
- Maximum Shear Stress Theory
- Match List I with List IIChoose the correct answer from the options given below :
List I List II A. Shear force (unit) I. Newton/Area B. Stress II. Newton C. Stain III. Lateral Stain / Axial Stain D. Poisson Ration (N) IV. Change in length / Actual length - CUET (PG) - 2023
- Water Resources Engineering
- Maximum Shear Stress Theory
View More Questions
Questions Asked in GATE PI exam
- A metallic cylindrical pressure vessel, used to store compressed air in a plant, has 1 m mean radius and 4 mm wall thickness. The maximum allowable normal and shear stresses in the cylindrical portion of the vessel are 100 MPa and 40 MPa, respectively. Considering only these data in the design, the maximum allowable internal gauge pressure (in MPa) of the compressed air is ______ . (Rounded off to 2 decimal places)
- GATE PI - 2024
- Stress-Strain behavior of metals and alloys
- The following differential equation governs the evolution of variable \(x(t)\) with time \(t, t \geq 0\).
\(\frac {d^2x}{dt^2} + 4x = e^{-t}\)
Given the initial conditions \(x = 0\) and \(\frac {dx}{dt} = 0\) at \(t = 0\), the value of \(x\) at \(t =\frac {\pi}{8}\) is _____ . (Rounded off to 3 decimal places)- GATE PI - 2024
- Differential Equations
- A CNC milling operation is carried out by moving the tool from the point A to point B in anti-clockwise direction to cut a slot of quarter circle with center at C, as shown. The coordinates of the points A and B are (0,0) and (10,10), respectively. All dimensions are in mm. If the feed rate at point P along x-axis is 6 mm/min, then the feed rate (in mm/min) at point P along y-axis is ______ . (Rounded off to 1 decimal place)
- GATE PI - 2024
- Machining parameters and material removal rate
- In a sand mold, a sprue of height \(h_2=200\ mm\) is to be provided for maintaining the molten metal flow rate of \(10^6\ mm^3/s\). The height of liquid column above the point 2 is kept constant at \(h_c=25\ mm\). The cross-sectional areas of the sprue at points 2 and 3 are \(A_2\) and \(A_3\), respectively. The points 1 and 3 are at the atmospheric pressure. Assuming the gauge pressure at point 2 to be zero as the limiting case to prevent aspiration effect, the ratio \(\frac {A_3}{A_2}\) _____ . (Rounded off to 2 decimal places)
- GATE PI - 2024
- Fluid Mechanics
- An assembly line consists of three work stations (\(S_1, S_2\) and \(S_3\)) in series to assemble a toy. The times required to perform tasks at these stations are 6, 4 and T minutes, respectively. If the efficiency of the assembly line in the steady state is 75%, then the maximum value of T (in minutes) is _____ . (Answer in integer)
- GATE PI - 2024
- Production Control
View More Questions