Question:
Given below are two statements:
Statement - I: Rate of change of shear force (f) at any section of a loaded beam is equal to the Rate of Loading (w) at the section i.e. \(w=\frac{df}{dx}\)
Statement - II: Rate of change of bending moment at any section of a loaded beam represent the shear force (F) at the section is \(f=\frac{dm}{dx}.\)
In the light of the above statements, choose the correct answer from the options given below :
Given below are two statements:
Statement - I: Rate of change of shear force (f) at any section of a loaded beam is equal to the Rate of Loading (w) at the section i.e. \(w=\frac{df}{dx}\)
Statement - II: Rate of change of bending moment at any section of a loaded beam represent the shear force (F) at the section is \(f=\frac{dm}{dx}.\)
In the light of the above statements, choose the correct answer from the options given below :
Statement - I: Rate of change of shear force (f) at any section of a loaded beam is equal to the Rate of Loading (w) at the section i.e. \(w=\frac{df}{dx}\)
Statement - II: Rate of change of bending moment at any section of a loaded beam represent the shear force (F) at the section is \(f=\frac{dm}{dx}.\)
In the light of the above statements, choose the correct answer from the options given below :
Updated On: Mar 21, 2024
- Both Statement I and Statement II are correct.
- Both Statement I and Statement II are incorrect.
- Statement I is correct but Statement II is incorrect.
- Statement I is incorrect but Statement II is correct.
Hide Solution
Verified By Collegedunia
The Correct Option is A
Solution and Explanation
The correct answer is (A) : Both Statement I and Statement II are correct.
Was this answer helpful?
0
0
Top Questions on Maximum Shear Stress Theory
- In a forming operation, the plastic deformation of a steel specimen starts under plane stress condition, where the principal stresses are \(σ_1=200\ Mpa\) and \(σ_2 = 100\ Mpa\). If the steel specimen follows von-Mises yield criterion, then the uniaxial tensile yield strength (in Mpa) of this steel material is ____ . (Rounded off to 1 decimal place)
- GATE PI - 2024
- Strength of Materials
- Maximum Shear Stress Theory
- For a mild steel specimen subjected to uniaxial tensile load, which of the following is/are TRUE?
- GATE PI - 2024
- Strength of Materials
- Maximum Shear Stress Theory
- A cantilever beam of T cross-section carries uniformly distributed load. Where does the maximum magnitude of the bending stress occur?
- CUET (PG) - 2023
- Water Resources Engineering
- Maximum Shear Stress Theory
- In a direct shear test, the shear strength and normal stress on a dry sand sample at failure are 0.6 kg/cm2 and 10 kg/cm2, respectively. The angle of internal friction of the sand will be nearly
- CUET (PG) - 2023
- Water Resources Engineering
- Maximum Shear Stress Theory
- Match List I with List IIChoose the correct answer from the options given below :
List I List II A. Shear force (unit) I. Newton/Area B. Stress II. Newton C. Stain III. Lateral Stain / Axial Stain D. Poisson Ration (N) IV. Change in length / Actual length - CUET (PG) - 2023
- Water Resources Engineering
- Maximum Shear Stress Theory
View More Questions
Questions Asked in CUET PG exam
- Find out the degree of the differential equation \(\frac {d^2t}{ds^2}+(\frac {dt}{ds})^2+2t=0\)
- CUET (PG) - 2023
- Differential Equations
- The surface area of the sphere x2 + y2 + z2 = 9 lying inside the cylinder x2 + y2 = 3y is
- CUET (PG) - 2023
- Surface Area of Cube, Cuboid and Cylinder
- The Ombudsman in a newspaper organisation represents the point of view of the ___.
- CUET (PG) - 2023
- Journalism
- The orthogonal trajectories of the family of curves y = \(ax^3\) is
- The minimum distance of the point (3, 4, 12) from the sphere x2 + y2 + z2 = 1 is
- CUET (PG) - 2023
- Coordinate Geometry
View More Questions