Question:
Which of the following is NOT a part of the dashboard of a tractor?
Which of the following is NOT a part of the dashboard of a tractor?
Show Hint
The dashboard includes gauges and switches, while the steering wheel is part of the control mechanism.
Updated On: June 02, 2025
- Main Switch
- Decompression Lever
- Water Temperature Gauge
- Steering Wheel
Hide Solution
Verified By Collegedunia
The Correct Option is D
Solution and Explanation
Step 1: Understanding the Dashboard Components
The dashboard of a tractor includes essential controls and monitoring devices.
Step 2: Identifying the Incorrect Option
- Main Switch: Controls the tractor’s ignition. - Decompression Lever: Helps in starting the engine. - Water Temperature Gauge: Monitors engine temperature. - Steering Wheel: Not part of the dashboard, but an external control component.
Step 3: Conclusion
The steering wheel is separate from the dashboard and does not belong in this category.
The dashboard of a tractor includes essential controls and monitoring devices.
Step 2: Identifying the Incorrect Option
- Main Switch: Controls the tractor’s ignition. - Decompression Lever: Helps in starting the engine. - Water Temperature Gauge: Monitors engine temperature. - Steering Wheel: Not part of the dashboard, but an external control component.
Step 3: Conclusion
The steering wheel is separate from the dashboard and does not belong in this category.
Was this answer helpful?
0
0
Top Questions on Tractors and Power Tillers
- A mouldboard plough is operated by a 2WD tractor with 6.0 kN pull. The ratio of lateral component to the longitudinal component of soil forces is 0.30, and the ratio of the vertical component to the longitudinal component of soil forces is 0.50. If the diameter of the driving wheels is 1.2 m and the rear axle rotates at 10 rpm, the drawbar power produced at 20% wheel slip is _________ kW. (Rounded off to 2 decimal places)
- GATE AG - 2025
- Farm Machinery
- Tractors and Power Tillers
- The height of the CG of a 4WD tractor with equal tread (1.25 m) in front and rear is 0.85 m. The tractor overturns during turning at a speed of 18 km.h\(^{-1}\). Neglecting the frictional forces on the tractor wheels, the turning radius is _________ m. (Rounded off to 2 decimal places)
- GATE AG - 2025
- Farm Machinery
- Tractors and Power Tillers
- Front wheel pivot points of a 2WD tractor are 1.2 m apart. When making turn on a flat concrete surface, the inner front wheel makes 50$^\circ$ and the outer front wheel makes 35$^\circ$ steering angles. To ensure turning without front wheel skid, the wheel base of the tractor should be _________ m. (Rounded off to 2 decimal places)
- GATE AG - 2025
- Farm Machinery
- Tractors and Power Tillers
- The nominal radius of the rear wheels of a 2WD tractor is 0.5 m. The rolling radius of the tire is 6% less than the nominal radius. While conducting a field test, if the actual distance covered for 20 revolutions of the rear wheel is found to be 56 m, the rear wheel slip is _________% (Rounded off to 2 decimal places).
- GATE AG - 2025
- Farm Machinery
- Tractors and Power Tillers
- While studying vertical motion imparted to the base of tractor seat, \( \theta \) (radian) is considered as rotation about tractor’s CG and \( R \) is considered as longitudinal distance from operator’s seat to the tractor’s CG. For a small value of \( \theta \), the term ‘\( R\theta \)’ represents the vertical motion resulting from tractor’s _________
- GATE AG - 2025
- Farm Machinery
- Tractors and Power Tillers
View More Questions
Questions Asked in TANCET exam
- What letter replaces the question mark?
- An intermediate shaft of a gearbox, supporting two spur gears A and B and mounted between two bearings C1 and C2, is shown in the below figure. The pitch circle diameters of gears A and B are 500 and 250 mm respectively. The shaft is made of alloy steel 20MnCr5. (\( S_{ut} = 620 \) and \( S_{yt} = 480 \) N/mm\(^2\)). The factors \( k_b \) and \( k_t \) of the ASME code are 2 and 1.5 respectively. The gears are keyed to the shaft. Determine the shaft diameter using the ASME code.
- TANCET - 2024
- Machine Design
- A train moving at 108 km/hr crosses a platform in 30 seconds. Then it crosses a man running at 12 km/hr in the same direction in 9 seconds. What is the length of train and platform in m?
- TANCET - 2024
- Time, Speed and Distance
- The speed of a motor boat in still water is 7km/hr. If the speed of the motor boat against the stream is 5 km/hr, what is the speed of the stream?
- TANCET - 2024
- Time, Speed and Distance
A closed-loop system has the characteristic equation given by: $ s^3 + k s^2 + (k+2) s + 3 = 0 $.
For the system to be stable, the value of $ k $ is:- TANCET - 2024
- Microprocessors
View More Questions
