The wettability of a surface by a liquid depends primarily on
- angle of contact between the surface and the liquid
- viscosity
- surface tension
- density
The Correct Option is A
Solution and Explanation
Top Questions on Surface Tension
Consider a water tank shown in the figure. It has one wall at \(x = L\) and can be taken to be very wide in the z direction. When filled with a liquid of surface tension \(S\) and density \( \rho \), the liquid surface makes angle \( \theta_0 \) (\( \theta_0 < < 1 \)) with the x-axis at \(x = L\). If \(y(x)\) is the height of the surface then the equation for \(y(x)\) is: (take \(g\) as the acceleration due to gravity)
- NEET (UG) - 2025
- Physics
- Surface Tension
- A spherical air bubble is formed inside a liquid (like water). The radius of the bubble is 0.5 mm, and the surface tension of the liquid is 0.072 N/m. What is the pressure inside the bubble relative to the outside pressure?
- MHT CET - 2025
- Physics
- Surface Tension
- A balloon is made of a material of surface tension S and has a small outlet. It is filled with air of density \( \rho \). Initially the balloon is a sphere of radius R. When the gas is allowed to flow out slowly at a constant rate, its radius shrinks as \( r(t) \). Assume that the pressure inside the balloon is \( P(r) \) and is more than the outside pressure (\( P_0 \)) by an amount proportional to the surface tension and inversely proportional to the radius. The balloon bursts when its radius reaches \( r_0 \). Then the speed of gas coming out of the balloon at \( r = R \) is :
- NEET (UG) - 2025
- Physics
- Surface Tension
- When the angle of contact between a solid and a liquid is \( 90^\circ \), then
- UPCATET - 2025
- Physics
- Surface Tension
- If two soap bubbles A and B of radii \(r_1\) and \(r_2\) respectively are kept in vaccum at constant temperature, then the ratio of masses of air inside the bubbles A and B is
- AP EAPCET - 2025
- Physics
- Surface Tension
Questions Asked in NEET exam
A sphere of radius R is cut from a larger solid sphere of radius 2R as shown in the figure. The ratio of the moment of inertia of the smaller sphere to that of the rest part of the sphere about the Y-axis is :
- NEET (UG) - 2025
- Moment Of Inertia
The current passing through the battery in the given circuit, is:
- NEET (UG) - 2025
- Current electricity
A bob of heavy mass \(m\) is suspended by a light string of length \(l\). The bob is given a horizontal velocity \(v_0\) as shown in figure. If the string gets slack at some point P making an angle \( \theta \) from the horizontal, the ratio of the speed \(v\) of the bob at point P to its initial speed \(v_0\) is :
- NEET (UG) - 2025
- Pendulums
- Two cities X and Y are connected by a regular bus service with a bus leaving in either direction every T min. A girl is driving scooty with a speed of 60 km/h in the direction X to Y. She notices that a bus goes past her every 30 minutes in the direction of her motion, and every 10 minutes in the opposite direction. Choose the correct option for the period T of the bus service and the speed (assumed constant) of the buses.
- NEET (UG) - 2025
- Relative Velocity
- The intensity of transmitted light when a polaroid sheet, placed between two crossed polaroids at \(22.5^\circ\) from the polarization axis of one of the polaroids (\(I_0\) is the intensity of polarised light after passing through the first polaroid):
- NEET (UG) - 2025
- Polarization
Concepts Used:
Surface Tension
The amount of energy required to increase the liquid's surface area by one unit area is known as surface tension. In other words, it is a property of the liquid surface to resist force.
Surface tension is defined as,
The ratio of the surface force F to the length L along which the force acts.
Mathematically, the surface tension formula can be expressed as follows:
T=F/L
Where,
- F is the force per unit length
- L is the length in which force act
- T is the surface tension of the liquid
Read More: Detergents and Surface Tension
Factors affecting surface tension:
- Impurities: The surface tension decreases with the addition of impurities.
- Surfactants: Adding surfactants in liquids lowers the tension of water making it interrupt aside or get susceptible.
- Temperature: The surface tension of a liquid reduces as the temperature rises.
The Unit of Surface Tension:
The SI unit of Surface Tension is Newton per Meter or N/m.