The following data are given in relation to turning operation of a cylindrical workpiece.
Diameter of the workpiece = 160 mm, length of the workpiece = 190 mm, cutting velocity = 80 m/min, and tool feed = 0.2 mm/rev.
Assuming the approach and the overrun of the tool to be 5 mm each, the machining time (in minutes) is _____ . (Answer in integer)
Diameter of the workpiece = 160 mm, length of the workpiece = 190 mm, cutting velocity = 80 m/min, and tool feed = 0.2 mm/rev.
Assuming the approach and the overrun of the tool to be 5 mm each, the machining time (in minutes) is _____ . (Answer in integer)
Correct Answer: 2
Solution and Explanation
Top Questions on Machine Tools
- The hole of size \(30.000\;\overset{\displaystyle +0.060}{0.000} \text{ mm}\) match with the shaft of size \(30.000\;\overset{\displaystyle +0.010}{0.000} \text{ mm}\) is on interchangeable arrangement. The assembly's maximum allowable clearance will be:
- Read the following statements for some properties:
(A) Pressure is an extensive property.
(B) Specific internal energy is intensive property.
(C) Enthalpy is extensive property.
(D) Temperature is intensive property.
(E) Specific heat is intensive property.
Choose the correct answer from the options given below: - Match List I with List IIChoose the correct answer from the options given below:
List I List II A. Line of action lying on the same line. I Parallel forces B. Lines of action parallel to each other. II Concurrent C. Lines of action intersecting at a point. III Non-Coplanar forces D. Lines of action lying on different planes or in space. IV Collinear forces - Match List I with List IIChoose the correct answer from the options given below:
List I List II A. Double, slides cranks mechanism I Pantograph B. Four bar chain II Elliptical trammel C. Single slider crank mechanism III Hip joint D. Spherical joint IV White worth quick returns mechanism - In a 2-DOF (RP) manipulator, the joint link parameters are given asThe final transformation matrix for this manipulator is S
Link i ai \(\alpha_i\) di \(\theta_i\) 1 0 \(90\degree\) 0 \(\theta_1\) 2 0 0 d2 0
Questions Asked in GATE PI exam
A regular dodecagon (12-sided regular polygon) is inscribed in a circle of radius \( r \) cm as shown in the figure. The side of the dodecagon is \( d \) cm. All the triangles (numbered 1 to 12 in the figure) are used to form squares of side \( r \) cm, and each numbered triangle is used only once to form a square. The number of squares that can be formed and the number of triangles required to form each square, respectively, are:
In the given figure, the numbers associated with the rectangle, triangle, and ellipse are 1, 2, and 3, respectively. Which one among the given options is the most appropriate combination of \( P \), \( Q \), and \( R \)?
- The left-hand side of a 20 cm thick wall is maintained at 25°C. The right-hand side of the wall is exposed to hot air at 50°C. There is no heat generation inside the wall and its thermal conductivity is 100 W/m·K. The convective heat transfer coefficient is 50 W/m²·K. Under steady state condition, the temperature (in °C) of the right-hand side surface of the wall is ........ (Rounded off to one decimal place).
- GATE PI - 2025
- Heat Transfer and Associated Losses
- Water flows through a smooth circular pipe of diameter 10 cm and length 10 m. The pressure drop across the length of the pipe is 0.2 Pa. Kinematic viscosity and density of water are \(1 \times 10^{-6} \, {m}^2/{s}\) and 1000 \({kg/m}^3\), respectively. Assuming laminar and fully developed flow throughout the pipe, the velocity of water (in mm/s) at the center of the pipe is ........ (Rounded off to one decimal place)
- GATE PI - 2025
- Fluid Mechanics
The table shows the data of running a machine for five years. The original machine cost is Rupees 70,000. In order to minimize the average total cost per year for running the machine, the machine should be replaced after ............. years. (Answer in integer)
- GATE PI - 2025
- Economic Activities