Match the engineering materials at room temperature with the given crystal structures.
Match the engineering materials at room temperature with the given crystal structures.
Show Hint
- P – 3, Q – 4, R – 1, S – 2
- P – 2, Q – 1, R – 4, S – 3
- P – 2, Q – 4, R – 1, S – 3
- P – 3, Q – 1, R – 4, S – 2
The Correct Option is A
Solution and Explanation
- Fe (Q) has a BCC structure.
- Al (R) has an FCC structure.
- Zn (S) has an HCP structure.
Thus, the correct matching is:
- P – 3 (Diamond Cubic)
- Q – 4 (BCC)
- R – 1 (FCC)
- S – 2 (HCP)
Top Questions on Material Science
- During tensile tests on mild steel specimens, the following points are observed:
(A) Elastic limit
(B) Proportionality limit
(C) Yield Point
(D) Fracture point
Choose the correct sequence of observation after the application of loading:- CUET (PG) - 2025
- Mechanical Engineering
- Material Science
- The ratio of is given as \( \frac{E{\lambda}_1 b_2}{E{\lambda}_1 b_1} \) is given as:
- CUET (PG) - 2025
- Mechanical Engineering
- Material Science
- Structural steel forms neck before it breaks. Neck formation starts
- CUET (PG) - 2025
- Mechanical Engineering
- Material Science
- In an FCC crystal with lattice parameter \(a\), consider the reaction of two leading partial dislocations, AB and CD, at the line of intersection of their slip planes \((111)\) and \((\bar{1}11)\), respectively. Dislocations AB and CD have Burgers vectors \(\vec{b}_1\) and \(\vec{b}_2\), respectively, as given in the figure. Which one of the following options for the slip plane and the Burgers vector of the resulting dislocation is correct?
- GATE XE - 2025
- Engineering Materials Science
- Material Science
- At 873 K, hydrogen diffuses under steady state through a 5 mm thick palladium sheet with a cross-sectional area of 0.3 m\(^2\). The concentrations of hydrogen at high and low pressure ends of the sheet are 3 kg m\(^{-3}\) and 0.5 kg m\(^{-3}\). The amount of hydrogen (in kg per day) passing through the sheet is (rounded off to two decimal places). Given: At 873 K, diffusivity of hydrogen = \(1.8 \times 10^{-8}\, m^2/s\).
- GATE XE - 2025
- Engineering Materials Science
- Material Science
Questions Asked in GATE PI exam
A regular dodecagon (12-sided regular polygon) is inscribed in a circle of radius \( r \) cm as shown in the figure. The side of the dodecagon is \( d \) cm. All the triangles (numbered 1 to 12 in the figure) are used to form squares of side \( r \) cm, and each numbered triangle is used only once to form a square. The number of squares that can be formed and the number of triangles required to form each square, respectively, are:
In the given figure, the numbers associated with the rectangle, triangle, and ellipse are 1, 2, and 3, respectively. Which one among the given options is the most appropriate combination of \( P \), \( Q \), and \( R \)?
- The left-hand side of a 20 cm thick wall is maintained at 25°C. The right-hand side of the wall is exposed to hot air at 50°C. There is no heat generation inside the wall and its thermal conductivity is 100 W/m·K. The convective heat transfer coefficient is 50 W/m²·K. Under steady state condition, the temperature (in °C) of the right-hand side surface of the wall is ........ (Rounded off to one decimal place).
- GATE PI - 2025
- Heat Transfer and Associated Losses
- Water flows through a smooth circular pipe of diameter 10 cm and length 10 m. The pressure drop across the length of the pipe is 0.2 Pa. Kinematic viscosity and density of water are \(1 \times 10^{-6} \, {m}^2/{s}\) and 1000 \({kg/m}^3\), respectively. Assuming laminar and fully developed flow throughout the pipe, the velocity of water (in mm/s) at the center of the pipe is ........ (Rounded off to one decimal place)
- GATE PI - 2025
- Fluid Mechanics
The table shows the data of running a machine for five years. The original machine cost is Rupees 70,000. In order to minimize the average total cost per year for running the machine, the machine should be replaced after ............. years. (Answer in integer)
- GATE PI - 2025
- Economic Activities