Question:
In a time study, the average time taken for packaging a product in a warehouse by a worker with 120% performance rating is observed as 9 minutes. Assuming an allowance of 10% of the standard time, the standard time (in minutes) for packaging is ______ . (Answer in integer)
In a time study, the average time taken for packaging a product in a warehouse by a worker with 120% performance rating is observed as 9 minutes. Assuming an allowance of 10% of the standard time, the standard time (in minutes) for packaging is ______ . (Answer in integer)
Updated On: Feb 10, 2025
Hide Solution
Verified By Collegedunia
Correct Answer: 12
Solution and Explanation
The answer is: 12.
Was this answer helpful?
0
1
Questions Asked in GATE PI exam
- In a sand mold, a sprue of height \(h_2=200\ mm\) is to be provided for maintaining the molten metal flow rate of \(10^6\ mm^3/s\). The height of liquid column above the point 2 is kept constant at \(h_c=25\ mm\). The cross-sectional areas of the sprue at points 2 and 3 are \(A_2\) and \(A_3\), respectively. The points 1 and 3 are at the atmospheric pressure. Assuming the gauge pressure at point 2 to be zero as the limiting case to prevent aspiration effect, the ratio \(\frac {A_3}{A_2}\) _____ . (Rounded off to 2 decimal places)
- GATE PI - 2024
- Fluid Mechanics
- A company purchased two machines, Machine A and Machine B, at the same time. The purchase price, estimated useful life and the estimated salvage value of the two machines are given in the table.Using the straight-line depreciation method for both the machines, the difference (in INR) between the value of Machine A and the value of Machine B at the end of five years is _____ . (Answer in integer)
Machine A Machine B Purchase price INR 20,000 INR 15,000 Estimated useful life 10 years 20 years Estimated salvage value INR 5,000 INR 5,000 - GATE PI - 2024
- Project Management
- A CNC milling operation is carried out by moving the tool from the point A to point B in anti-clockwise direction to cut a slot of quarter circle with center at C, as shown. The coordinates of the points A and B are (0,0) and (10,10), respectively. All dimensions are in mm. If the feed rate at point P along x-axis is 6 mm/min, then the feed rate (in mm/min) at point P along y-axis is ______ . (Rounded off to 1 decimal place)
- GATE PI - 2024
- Machining parameters and material removal rate
- The following differential equation governs the evolution of variable \(x(t)\) with time \(t, t \geq 0\).
\(\frac {d^2x}{dt^2} + 4x = e^{-t}\)
Given the initial conditions \(x = 0\) and \(\frac {dx}{dt} = 0\) at \(t = 0\), the value of \(x\) at \(t =\frac {\pi}{8}\) is _____ . (Rounded off to 3 decimal places)- GATE PI - 2024
- Differential Equations
- An irrigation pump is used to draw water from a pond. One end of a 5.05 cm diameter hose pipe is connected to the outlet of the pump at 1.02 m below the surface level, and just after the pump, the static gauge pressure and flow rate of the water are 50 kPa and 8 kg/s, respectively. The pumped water is discharged at the ground level through a nozzle. Assume that the flow through the hose pipe and nozzle is steady and laminar, and frictional and viscous losses are negligible. The density of water is 1000 kg/m3 and the acceleration due to gravity is 9.81 m/s2. If the static pressure at the nose/exit of the nozzle just reduces to atmospheric pressure then the nose diameter (in cm) of the nozzle is _____ . (Rounded off to 2 decimal places)
- GATE PI - 2024
- Thermal and Fluids Engineering
View More Questions