Question:
In a single pass cold rolling operation, a flat plate is reduced to a thickness of 3 mm. In this operation, two rolls of diameter 400 mm each are rotating in opposite direction at 300 RPM, and the elastic deflection of these rolls is negligible. The angle of bite is 10°. If the neutral point is present at an angle of 7° from the exit side, then the thickness of the plate (in mm) at the neutral point is _____ . (Rounded off to 1 decimal place)
In a single pass cold rolling operation, a flat plate is reduced to a thickness of 3 mm. In this operation, two rolls of diameter 400 mm each are rotating in opposite direction at 300 RPM, and the elastic deflection of these rolls is negligible. The angle of bite is 10°. If the neutral point is present at an angle of 7° from the exit side, then the thickness of the plate (in mm) at the neutral point is _____ . (Rounded off to 1 decimal place)
Updated On: Jul 17, 2024
Hide Solution
Verified By Collegedunia
Correct Answer: 5.8
Solution and Explanation
The answer is: 5.8 or 6.1(approx.)
Was this answer helpful?
0
0
Top Questions on Metal Forming
- A blank of 100 mm diameter is to be cut out of a 2 mm thick sheet through blanking operation. If the radial clearance between the punch and die is 6% of the sheet thickness then the diameter (in mm) of the punch is _____ . (Rounded off to 2 decimal places)
- GATE PI - 2024
- Manufacturing Processes I
- Metal Forming
- Which one of the following pure metals has the hexagonal close packed (HCP) crystal structure at room temperature?
Questions Asked in GATE PI exam
- A metallic cylindrical pressure vessel, used to store compressed air in a plant, has 1 m mean radius and 4 mm wall thickness. The maximum allowable normal and shear stresses in the cylindrical portion of the vessel are 100 MPa and 40 MPa, respectively. Considering only these data in the design, the maximum allowable internal gauge pressure (in MPa) of the compressed air is ______ . (Rounded off to 2 decimal places)
- GATE PI - 2024
- Stress-Strain behavior of metals and alloys
- The following differential equation governs the evolution of variable \(x(t)\) with time \(t, t \geq 0\).
\(\frac {d^2x}{dt^2} + 4x = e^{-t}\)
Given the initial conditions \(x = 0\) and \(\frac {dx}{dt} = 0\) at \(t = 0\), the value of \(x\) at \(t =\frac {\pi}{8}\) is _____ . (Rounded off to 3 decimal places)- GATE PI - 2024
- Differential Equations
- A CNC milling operation is carried out by moving the tool from the point A to point B in anti-clockwise direction to cut a slot of quarter circle with center at C, as shown. The coordinates of the points A and B are (0,0) and (10,10), respectively. All dimensions are in mm. If the feed rate at point P along x-axis is 6 mm/min, then the feed rate (in mm/min) at point P along y-axis is ______ . (Rounded off to 1 decimal place)
- GATE PI - 2024
- Machining parameters and material removal rate
- In a sand mold, a sprue of height \(h_2=200\ mm\) is to be provided for maintaining the molten metal flow rate of \(10^6\ mm^3/s\). The height of liquid column above the point 2 is kept constant at \(h_c=25\ mm\). The cross-sectional areas of the sprue at points 2 and 3 are \(A_2\) and \(A_3\), respectively. The points 1 and 3 are at the atmospheric pressure. Assuming the gauge pressure at point 2 to be zero as the limiting case to prevent aspiration effect, the ratio \(\frac {A_3}{A_2}\) _____ . (Rounded off to 2 decimal places)
- GATE PI - 2024
- Fluid Mechanics
- An assembly line consists of three work stations (\(S_1, S_2\) and \(S_3\)) in series to assemble a toy. The times required to perform tasks at these stations are 6, 4 and T minutes, respectively. If the efficiency of the assembly line in the steady state is 75%, then the maximum value of T (in minutes) is _____ . (Answer in integer)
- GATE PI - 2024
- Production Control
View More Questions