At 25°C,the dissociation constant of a base, BOH, is 1.0 x 10-12. The concentration of hydroxyl ions in 0.01 M aqueous solution of the base would be:
1.0 x 10-6 mol L-1
1.0 x 10-5 mol L-1
1.0 x 10-8 mol L-1
1.0 x 10-7 mol L-1
The Correct Option is D
Solution and Explanation
BOH ⇌ B+ +OH-
Kb =\(\frac{[B^+][OH^-]}{[BOH]}\)
\(\therefore\) 1×10-12 = 0.01 [OH- ]2
(\(\because\) [OH- ]=[B+ ])
\(\therefore\) [OH- ]2 =10−14
\(\therefore\) [OH- ] =10−7
M \(\Rightarrow\) 1.0×10-7 mol L-1
Therefore, the correct option is (D): 1.0×10-7 mol L-1
Top Questions on Thermodynamics
The standard heat of formation, in kcal/mol, of $Ba^{2+}$ is:
Given: Standard heat of formation of SO₄²⁻(aq) = -216 kcal/mol, standard heat of crystallization of BaSO₄(s) = -4.5 kcal/mol, standard heat of formation of BaSO₄(s) = -349 kcal/mol.- NEET (UG) - 2025
- Chemistry
- Thermodynamics
- A piston-cylinder assembly having 250 mm diameter contains 0.01 kg of water vapor at 1 MPa and 200°C. The specific volume of the vapor is 0.020602 m\(^3\)/kg. The system expands as per the relation \( p v^n = {constant} \), where \( p \) is pressure and \( v \) is the specific volume. The expansion of water vapor displaces the piston by 50 mm. If the final pressure is 0.35 MPa, the value of the exponent \( n \) is ........ (rounded off to two decimal places).
- GATE XE - 2025
- Engineering Sciences
- Thermodynamics
A stream of superheated steam (2 MPa, 300°C) mixes with another stream of superheated steam (2 MPa, 400°C) through a steady-state adiabatic process. The flow rates of the streams are 3 kg/min and 2 kg/min, respectively. This mixture then expands in an adiabatic nozzle to a saturated mixture with quality of 0.77 and 1 kPa. Neglect the velocity at the nozzle entrance and the change in potential energies. The velocity at the nozzle exit (in m/s) is ......... (rounded off to two decimal places).
Use the following data:
At 2 MPa, 300 °C: Specific enthalpy of superheated steam = 3024.2 kJ/kg
At 2 MPa, 400 °C: Specific enthalpy of superheated steam = 3248.4 kJ/kg
At 1 kPa: Specific enthalpy of saturated water = 29.3 kJ/kg
At 1 kPa: Specific enthalpy of saturated vapour = 2513.7 kJ/kg
- GATE XE - 2025
- Engineering Sciences
- Thermodynamics
- Consider a gas obeying the relation \( P(v - b) = RT \), where \( b \) and \( R \) are constants. Which of the following statement(s) is/are CORRECT about the specific heat capacity at constant pressure?
- GATE XE - 2025
- Engineering Sciences
- Thermodynamics
- A rigid tank of 300 litre capacity contains 3 kg of oxygen (molar mass = 32 kg/kmol) at 25°C. If oxygen behaves as an ideal gas, the pressure (in kPa) inside the tank is ......... (rounded off to two decimal places).
Use: Universal gas constant \( R_u = 8.314 \, {kJ/kmol-K} \)
- GATE XE - 2025
- Engineering Sciences
- Thermodynamics
Questions Asked in NEET exam
- Given below are two statements:
Statement I: Fig fruit is a non-vegetarian fruit as it has enclosed fig wasps in it.
Statement II: Fig wasp and fig tree exhibit a mutual relationship as the fig wasp completes its life cycle in the fig fruit and the fig fruit gets pollinated by the fig wasp. - A wire of resistance \(R\) is cut into 8 equal pieces. From these pieces, two equivalent resistances are made by adding four of these together in parallel. Then these two are added in series. The net effective resistance of the combination is:
- NEET (UG) - 2025
- Resistance
- An oxygen cylinder of volume 30 litre has 18.20 moles of oxygen. After some oxygen is withdrawn from the cylinder, its gauge pressure drops to 11 atmospheric pressure at temperature \(27^\circ\)C. The mass of the oxygen withdrawn from the cylinder is nearly equal to: [Given, \(R = \frac{100}{12} \text{ J mol}^{-1} \text{K}^{-1}\), and molecular mass of \(O_2 = 32 \text{ g/mol}\), 1 atm pressure = \(1.01 \times 10^5 \text{ N/m}^2\)]
- NEET (UG) - 2025
- Ideal-gas equation and absolute temperature
The current passing through the battery in the given circuit, is:
- NEET (UG) - 2025
- Current electricity
Three identical heat conducting rods are connected in series as shown in the figure. The rods on the sides have thermal conductivity 2K while that in the middle has thermal conductivity K. The left end of the combination is maintained at temperature 3T and the right end at T. The rods are thermally insulated from outside. In steady state, temperature at the left junction is \(T_1\) and that at the right junction is \(T_2\). The ratio \(T_1 / T_2\) is
- NEET (UG) - 2025
- Conductivity-thermal and electrical
Concepts Used:
Enthalpy change
Enthalpy Change refers to the difference between the heat content of the initial and final state of the reaction. Change in enthalpy can prove to be of great importance to find whether the reaction is exothermic or endothermic.
Formula for change in enthalpy is:-
dH = dU + d(PV)
The above equation can be written in the terms of initial and final states of the system which is defined below:
UF – UI = qP –p(VF – VI)
Or qP = (UF + pVF) – (UI + pVI)
Enthalpy (H) can be written as H= U + PV. Putting the value in the above equation, we obtained:
qP = HF – HI = ∆H
Hence, change in enthalpy ∆H = qP, referred to as the heat consumed at a constant pressure by the system. At constant pressure, we can also write,
∆H = ∆U + p∆V
Standard Enthalpy of Reaction
To specify the standard enthalpy of any reaction, it is calculated when all the components participating in the reaction i.e., the reactants and the products are in their standard form. Therefore the standard enthalpy of reaction is the enthalpy change that occurs in a system when a matter is transformed by a chemical reaction under standard conditions.