Question:
Which type of error is caused due to faulty calibration of instruments?
Which type of error is caused due to faulty calibration of instruments?
Show Hint
Errors due to instrument defects or calibration issues always fall under systematic errors.
Updated On: Feb 7, 2026
- Gross error
- Random error
- Systematic error
- Environmental error
Hide Solution
Verified By Collegedunia
The Correct Option is C
Solution and Explanation
Step 1: Understanding measurement errors.
Measurement errors occur when the observed value differs from the true value. These errors can arise due to human mistakes, instrument faults, or external conditions.
Step 2: Understanding systematic errors.
Systematic errors are consistent and repeatable errors that occur due to faults in the measuring instrument, improper calibration, or incorrect zero setting. Faulty calibration causes the instrument to give biased readings in the same direction every time.
Step 3: Analyzing the options.
(A) Gross error: These are caused by human mistakes such as incorrect reading or recording.
(B) Random error: These occur due to unpredictable variations and do not follow a fixed pattern.
(C) Systematic error: Correct — faulty calibration causes a consistent deviation in measurements, which is the definition of systematic error.
(D) Environmental error: These errors arise due to changes in temperature, humidity, or pressure.
Step 4: Conclusion.
Since faulty calibration produces consistent and repeatable errors, it results in systematic error.
Measurement errors occur when the observed value differs from the true value. These errors can arise due to human mistakes, instrument faults, or external conditions.
Step 2: Understanding systematic errors.
Systematic errors are consistent and repeatable errors that occur due to faults in the measuring instrument, improper calibration, or incorrect zero setting. Faulty calibration causes the instrument to give biased readings in the same direction every time.
Step 3: Analyzing the options.
(A) Gross error: These are caused by human mistakes such as incorrect reading or recording.
(B) Random error: These occur due to unpredictable variations and do not follow a fixed pattern.
(C) Systematic error: Correct — faulty calibration causes a consistent deviation in measurements, which is the definition of systematic error.
(D) Environmental error: These errors arise due to changes in temperature, humidity, or pressure.
Step 4: Conclusion.
Since faulty calibration produces consistent and repeatable errors, it results in systematic error.
Was this answer helpful?
0
0
Top Questions on Measurements
- Which of the following transducers is most suitable for measuring very small displacements?
- A metallic strain-gauge (SG) with resistance $R_{SG}$ is connected as shown in the figure, where $R_{L1}$, $R_{L2}$, $R_{L3}$ represent the lead wire resistances. The SG has a gauge factor of 2 and nominal resistance $R_N$ of $125 \Omega$. When the SG is subjected to a tensile strain of $2 \times 10^{-3}$, the resulting change in $R_{SG}$ is $\Delta R$. The $\Delta R$ value is measured as $\Delta R_{MEAS} = R_{EQ2} - R_{EQ1}$. The $R_{EQ1}$ and $R_{EQ2}$ are the equivalent resistances measured between the terminals 1 and 2, and terminals 2 and 3, respectively. If $R_{L1} = R_{L2} = 5 \Omega$, and $R_{L3} = 4.95 \Omega$, the measured value of tensile strain is ________ $\times 10^{-3}$ (rounded off to two decimal places).
- A metallic strain-gauge (SG) with resistance \( R_{SG} \) is connected as shown in the figure, where \( R_{L1} \), \( R_{L2} \), \( R_{L3} \) represent the lead wire resistances. The SG has a gauge factor of 2 and nominal resistance \( R_N \) of \( 125 \, \Omega \). When the SG is subjected to a tensile strain of \( 2 \times 10^{-3} \), the resulting change in \( R_{SG} \) is \( \Delta R \). The \( \Delta R \) value is measured as \( \Delta R_{MEAS} = R_{EQ2} - R_{EQ1} \). The \( R_{EQ1} \) and \( R_{EQ2} \) are the equivalent resistances measured between the terminals 1 and 2, and terminals 2 and 3, respectively.
If \( R_{L1} = R_{L2} = 5 \, \Omega \), and \( R_{L3} = 4.95 \, \Omega \), the measured value of tensile strain is ________ \( \times 10^{-3} \) (rounded off to two decimal places). - Power consumed by a three-phase balanced load is measured using two-wattmeter method. The per-phase average power drawn by the load is 30 kW at \( \frac{\sqrt{3}}{2} \) lagging power factor. The readings of the wattmeters will be
- An oscilloscope has an input resistance of \( 1\, {M}\Omega \). A 10X passive attenuating probe is connected to it to increase the input voltage range as well as the effective input resistance. The effective input resistance, in \( {M}\Omega \), seen into the probe tip is:
View More Questions
Questions Asked in GATE IN exam
- The Laplace transform of a unit step function \( u(t) \) is:
- GATE IN - 2026
- Signals
- In amplitude modulation, the modulation index should be:
- GATE IN - 2026
- communication systems
- How many flip-flops are required to design a MOD-10 counter?
- GATE IN - 2026
- Electrical Circuits
- An ideal operational amplifier has:
- GATE IN - 2026
- Analog Electronics
- For a stable linear time-invariant system, the location of all poles must be:
- GATE IN - 2026
- Control Systems
View More Questions