Question:
Which of the following is NOT a derivative of digital elevation model (DEM)?
Which of the following is NOT a derivative of digital elevation model (DEM)?
Updated On: Jul 12, 2024
- Slope
- Aspect
- Contour
- Emissivity
Hide Solution
Verified By Collegedunia
The Correct Option is D
Solution and Explanation
The correct answer is (D) : Emissivity
Was this answer helpful?
0
0
Top Questions on Distance and angle measurement
- To reduce the slope distance (S) to an equivalent horizontal distance (H) as shown in the figure given below, the following independent observations were taken.
\(S = 29.95 m ± 0.01 m; \theta = 4°30' ± 10' \)
The required precision of computed horizontal distance is ± 0.005 m. Assume a "balanced accuracy" where the contribution to precision of the horizontal distance comes equally from the slope distance and angle measurements. The minimum number of angle observations to achieve the desired precision is
(Given 1 radian = 206265 seconds)
- GATE CE - 2024
- Geomatics Engineering
- Distance and angle measurement
- In tangential method of tacheometry, two vanes in a staff were fixed at a distance of 1.0 m with the bottom vane fixed at 1.0 m. The levelling staff was held vertical at a point P and the vertical angles of the vanes observed were 5°30′ and 3°15', respectively. The vertical distance between the instrument axis and the bottom vane would be _______ m (rounded off to two decimal places).
- GATE CE - 2024
- Geomatics Engineering
- Distance and angle measurement
- Independent angles AOB, BOC and AOC were observed as shown in figure. The standard error of all observations is same. The adjusted values of these angles using the least squares adjustment are
- GATE CE - 2024
- Geomatics Engineering
- Distance and angle measurement
- A bird is resting on a point P at a height of 8 m above the Mean Sea Level (MSL). Upon hearing a loud noise, the bird flies parallel to the ground surface and reaches a point Q which is located at a height of 3 m above MSL. The ground surface has a falling gradient of 1 in 2. Ignoring the effects of curvature and refraction, the horizontal distance (in meters) between points P and Q is ______ (in integer).
- GATE CE - 2024
- Geomatics Engineering
- Distance and angle measurement
- Among the following statements relating the fundamental lines of a transit theodolite, which one is CORRECT?
- GATE CE - 2024
- Geomatics Engineering
- Distance and angle measurement
View More Questions
Questions Asked in GATE CE exam
- An electricity utility company charges ₹7 per kWh. If a 40-watt desk light is left on for 10 hours each night for 180 days, what would be the cost of energy consumption? If the desk light is on for 2 more hours each night for the 180 days, what would be the percentage-increase in the cost of energy consumption?
- GATE CE - 2025
- Logical and Analytical Reasoning Skills
- During determination of the bulk specific gravity of compacted bituminous specimen, the mass in air of the specimen is 1260 g and volume is 525 cm³. The density of water is 1.0 g/cm³. The theoretical maximum specific gravity of mix is 2.510. The percentage air voids in the compacted specimen is ......... (rounded off to 2 decimal places).
- GATE CE - 2025
- Gravity Dams and Spillways
In levelling between two points A and B on the opposite banks of a river, the readings are taken by setting the instrument both at A and B, as shown in the table. If the RL of A is 150.000 m, the RL of B (in m) is ....... (rounded off to 3 decimal places).
- GATE CE - 2025
- Surveying and Levelling
A one-way, single lane road has traffic that consists of 30% trucks and 70% cars. The speed of trucks (in km/h) is a uniform random variable on the interval (30, 60), and the speed of cars (in km/h) is a uniform random variable on the interval (40, 80). The speed limit on the road is 50 km/h. The percentage of vehicles that exceed the speed limit is ........ (rounded off to 1 decimal place).
- GATE CE - 2025
- Traffic signs
- A 5.0 m wide rectangular channel carries a discharge of 10 m³/s at a depth of 1.5 m under uniform flow. To produce critical flow conditions without affecting the upstream conditions, the channel bottom elevation should be raised (in m) by ........ (rounded off to 2 decimal places).
- GATE CE - 2025
- Microscopic and macroscopic parameters of traffic flow
View More Questions