Question:
In tangential method of tacheometry, two vanes in a staff were fixed at a distance of 1.0 m with the bottom vane fixed at 1.0 m. The levelling staff was held vertical at a point P and the vertical angles of the vanes observed were 5°30′ and 3°15', respectively. The vertical distance between the instrument axis and the bottom vane would be _______ m (rounded off to two decimal places).
In tangential method of tacheometry, two vanes in a staff were fixed at a distance of 1.0 m with the bottom vane fixed at 1.0 m. The levelling staff was held vertical at a point P and the vertical angles of the vanes observed were 5°30′ and 3°15', respectively. The vertical distance between the instrument axis and the bottom vane would be _______ m (rounded off to two decimal places).
Updated On: Jul 12, 2024
Hide Solution
Verified By Collegedunia
Correct Answer: 1.4
Solution and Explanation
The correct answer is : 1.40 to 1.50 (approx.)
Was this answer helpful?
0
0
Top Questions on Distance and angle measurement
- To reduce the slope distance (S) to an equivalent horizontal distance (H) as shown in the figure given below, the following independent observations were taken.
\(S = 29.95 m ± 0.01 m; \theta = 4°30' ± 10' \)
The required precision of computed horizontal distance is ± 0.005 m. Assume a "balanced accuracy" where the contribution to precision of the horizontal distance comes equally from the slope distance and angle measurements. The minimum number of angle observations to achieve the desired precision is
(Given 1 radian = 206265 seconds)
- GATE CE - 2024
- Geomatics Engineering
- Distance and angle measurement
- Independent angles AOB, BOC and AOC were observed as shown in figure. The standard error of all observations is same. The adjusted values of these angles using the least squares adjustment are
- GATE CE - 2024
- Geomatics Engineering
- Distance and angle measurement
- A bird is resting on a point P at a height of 8 m above the Mean Sea Level (MSL). Upon hearing a loud noise, the bird flies parallel to the ground surface and reaches a point Q which is located at a height of 3 m above MSL. The ground surface has a falling gradient of 1 in 2. Ignoring the effects of curvature and refraction, the horizontal distance (in meters) between points P and Q is ______ (in integer).
- GATE CE - 2024
- Geomatics Engineering
- Distance and angle measurement
- Among the following statements relating the fundamental lines of a transit theodolite, which one is CORRECT?
- GATE CE - 2024
- Geomatics Engineering
- Distance and angle measurement
- The histogram equalization applied to a digital image generally DOES NOT yield a truly uniform histogram of the transformed image due to
- GATE CE - 2024
- Geomatics Engineering
- Distance and angle measurement
View More Questions
Questions Asked in GATE CE exam
- Find the odd one out in the set: {19, 37, 21, 17, 23, 29, 31, 11}
- GATE CE - 2024
- Odd one Out
- A surveyor observes a zenith angle of 93° 00' 00" during a theodolite survey. The corresponding vertical angle is
- GATE CE - 2024
- Principles of surveying
- The initial cost of an equipment is Rs. 1,00,000. Its salvage value at the end of accounting life of 5 years is Rs. 10,000. The difference in depreciation (in Rs.) computed using 'double-declining balance method' and 'straight line method' of depreciation in Year-2 is ____ (in positive integer).
- GATE CE - 2024
- Construction Management
- A 2m × 2m tank of 3 m height has inflow, outflow and stirring mechanisms. Initially, the tank was half-filled with fresh water. At t = 0, an inflow of a salt solution of concentration 5 g/m3 at the rate of 2 litre/s and an outflow of the well stirred mixture at the rate of 1 litre/s are initiated. This process can be modelled using the following differential equation:
\(\frac {dm}{dt}+\frac {m}{6000+t}=0.01\)
where m is the mass (grams) of the salt at time t (seconds). The mass of the salt (in grams) in the tank at 75% of its capacity is _____ (rounded off to 2 decimal places).- GATE CE - 2024
- Properties of Fluids
- An inverted T-shaped concrete beam (B1) in the figure, with centroidal axis X - X, is subjected to an effective prestressing force of 1000 kN acting at the bottom kern point of the beam cross-section. Also consider an identical concrete beam (B2) with the same grade of concrete but without any prestressing force.
- GATE CE - 2024
- Concrete
View More Questions