Question:
Universal Transverse Mercator projection is:
Universal Transverse Mercator projection is:
Show Hint
The Universal Transverse Mercator (UTM) projection is a cylindrical projection commonly used for large-scale mapping.
Updated On: Feb 27, 2025
- \(\text{Conical projection} \)
- \(\text{Cylindrical projection} \)
- \(\text{Zenithal projection} \)
- \(\text{Planner projection} \)
Hide Solution
Verified By Collegedunia
The Correct Option is B
Solution and Explanation
Step 1: Understanding UTM projection.
The Universal Transverse Mercator (UTM) projection is a cylindrical map projection that divides the world into 60 zones.
Step 2: Explanation of other projection types. - Conical Projection: Best for mid-latitude regions. - Zenithal Projection: Used for mapping poles. - Planner Projection: Not a standard projection type.
Step 3: Selecting the correct option. Since UTM is a cylindrical projection, the correct answer is b. Cylindrical projection.
Step 2: Explanation of other projection types. - Conical Projection: Best for mid-latitude regions. - Zenithal Projection: Used for mapping poles. - Planner Projection: Not a standard projection type.
Step 3: Selecting the correct option. Since UTM is a cylindrical projection, the correct answer is b. Cylindrical projection.
Was this answer helpful?
0
0
Top Questions on General Cartography
- What will be the ground distance if the map distance on a 1:50,000 scale map is measured as 5 cm?
- TANCET - 2024
- Geo Informatics Engineering
- General Cartography
- An imaginary line drawn on a map joining places with the same rainfall is called:
- TANCET - 2024
- Geo Informatics Engineering
- General Cartography
- Projection most commonly used for mapping polar regions is:
- TANCET - 2024
- Geo Informatics Engineering
- General Cartography
- Match List I with List IIChoose the correct answer from the options given below:
LIST I LIST II A. Million sheet I. 4°x4° B. Quarter-inch sheet II. 1°x1° C. Half-inch sheet III. 30'x30' D. Special sheet IV. 7'30"x7'30" - CUET (PG) - 2024
- Applied Geography and Geoinformatics
- General Cartography
- Identify correct statements about flow diagrams:
(A) When part of the commodity is diverted to a different direction, the main flowline also becomes thicker proportionately.
(B) The thickness of the lines is determined by the volume or quantity of flow.
(C) Movement of goods can be shown only in one direction.
(D) These are not suitable to represent international, national or regional flow of various commodities.
Choose the correct answer from the options given below:- CUET (PG) - 2024
- Applied Geography and Geoinformatics
- General Cartography
View More Questions
Questions Asked in TANCET exam
- What letter replaces the question mark?
- An intermediate shaft of a gearbox, supporting two spur gears A and B and mounted between two bearings C1 and C2, is shown in the below figure. The pitch circle diameters of gears A and B are 500 and 250 mm respectively. The shaft is made of alloy steel 20MnCr5. (\( S_{ut} = 620 \) and \( S_{yt} = 480 \) N/mm\(^2\)). The factors \( k_b \) and \( k_t \) of the ASME code are 2 and 1.5 respectively. The gears are keyed to the shaft. Determine the shaft diameter using the ASME code.
- TANCET - 2024
- Machine Design
- A train moving at 108 km/hr crosses a platform in 30 seconds. Then it crosses a man running at 12 km/hr in the same direction in 9 seconds. What is the length of train and platform in m?
- TANCET - 2024
- Time, Speed and Distance
- The speed of a motor boat in still water is 7km/hr. If the speed of the motor boat against the stream is 5 km/hr, what is the speed of the stream?
- TANCET - 2024
- Time, Speed and Distance
A closed-loop system has the characteristic equation given by: $ s^3 + k s^2 + (k+2) s + 3 = 0 $.
For the system to be stable, the value of $ k $ is:- TANCET - 2024
- Microprocessors
View More Questions