The two-dimensional state of stress, in an infinitesimal element, is given by
\[
\sigma_{xx} = 800 \, {MPa}, \sigma_{xy} = 300 \, {MPa}, \sigma_{yy} = 0 \, {MPa}.
\]
Which one of the following options is the maximum shear stress (in MPa) in the element?
Show Hint
- 500
- 400
- 800
- 300
The Correct Option is A
Solution and Explanation
Step 1: The maximum shear stress in a two-dimensional stress state can be calculated using the following formula: \[ \tau_{{max}} = \frac{1}{2} \sqrt{ (\sigma_{xx} - \sigma_{yy})^2 + 4\sigma_{xy}^2 } \] where \( \sigma_{xx} \), \( \sigma_{yy} \), and \( \sigma_{xy} \) are the normal and shear stresses.
Step 2: Substituting the given values into the formula: \[ \tau_{{max}} = \frac{1}{2} \sqrt{ (800 - 0)^2 + 4(300)^2 } \] \[ \tau_{{max}} = \frac{1}{2} \sqrt{ 640000 + 360000 } \] \[ \tau_{{max}} = \frac{1}{2} \sqrt{ 1000000 } \] \[ \tau_{{max}} = \frac{1}{2} \times 1000 = 500 \, {MPa} \] Step 3: Therefore, the maximum shear stress is \( 500 \, {MPa} \), which corresponds to option (A).
Top Questions on Corrosion
The figure shows a rod PQ, hinged at P, rotating counter-clockwise with a uniform angular speed of 15 rad/s. A block R translates along a slot cut out in rod PQ. At the instant shown the distance \( PR = 0.5 \, {m} \) and \( \theta = 60^\circ \). The relative velocity of R with respect to the rod PQ is 5 m/s at the instant shown. The relative acceleration of R with respect to the rod PQ is zero at the instant shown.
Which one of the following is the CORRECT magnitude of the absolute acceleration (in m/s\(^2\)) of block R?
Consider two blocks, P of mass 100 kg and Q of mass 150 kg, resting as shown in the figure. The angle \( \theta = 30^\circ \). The coefficient of friction between the two blocks is 0.2. Assume no friction exists at all other interfaces. The minimum force required to move the block P upward is \( W \). Which one of the following options is closest to the CORRECT magnitude of \( W \) (in N)?
A force of \( P = 100 \, {N} \) is applied at the ends of the pliers as shown in the figure. Neglecting friction, the force exerted by the upper jaw on the workpiece is ........... N (in integer).
- For a certain linear elastic isotropic material, the Young’s modulus is 140 GPa and the shear modulus is 50 GPa. The Poisson’s ratio for the material is ........... (rounded off to two decimal places).
Consider a beam with a square box cross-section as shown in the figure. The outer square has a length of 10 mm. The thickness of the section is 1 mm. The area moment of inertia about the x-axis is ........... mm\(^4\) (in integer).
Questions Asked in GATE XE exam
In the figures given below, L and H indicate low and high pressure centers, respectively; PGF, CoF and CeF indicate Pressure Gradient Force, Coriolis Force and Centrifugal Force, respectively; \( V \) is Velocity. [The arrows indicate only the directions but not the magnitudes of the forces and velocity.]
Which of the following is/are the correct representation(s) of the directions of various forces and velocity in the gradient wind balance in the northern hemisphere?
- GATE XE - 2025
- Atmospheric Science
Which of the following is the correct form of the mass divergence form of the continuity equation for a compressible fluid? [In the given equations, \( \rho \) is the density and \( \nabla \) the three-dimensional velocity vector of the fluid.]
[(i)] $\displaystyle \frac{\partial \rho}{\partial t} + \nabla \times (\rho \mathbf{v}) = 0$
[(ii)] $\displaystyle \frac{\partial \rho}{\partial t} + \nabla \cdot (\rho \mathbf{v}) = 0$
[(iii)] $\displaystyle \frac{\partial \mathbf{v}}{\partial t} + \rho \cdot \nabla \mathbf{v} = 0$
[(iv)] $\displaystyle \frac{\partial \rho}{\partial t} + \mathbf{v} \cdot \nabla \rho = 0$- GATE XE - 2025
- Atmospheric Science
- The north-Atlantic deep-water is associated with .........
- GATE XE - 2025
- Indian Ocean Current Systems
- The zonal gradient of meridional current and the meridional gradient of zonal current is \( -0.3 \times 10^{-3} \, {s}^{-1} \) and \( 0.3 \times 10^{-3} \, {s}^{-1} \), respectively, at a location P (87°E, 15°N). Which one of the following best explains the nature of the flow?
- GATE XE - 2025
- Indian Ocean Current Systems
The vertical (depth) profiles for three parameters P1, P2, and P3 in the northern Indian Ocean are given in the figure below. The values along the x-axis are the normalized values of the parameters and y-axis is the depth (m).
Identify the parameters P1, P2, and P3 from the options given below.
- GATE XE - 2025
- Indian Ocean Current Systems