Question:
The structural design method that DOES NOT take into account the safety factors on the design loads is
The structural design method that DOES NOT take into account the safety factors on the design loads is
Updated On: Jul 18, 2024
- working stress method.
- load factor method.
- ultimate load method.
- limit state method.
Hide Solution
Verified By Collegedunia
The Correct Option is A
Solution and Explanation
The correct option is (A) : working stress method..
Was this answer helpful?
0
0
Top Questions on Working stress and Limit state design concepts
- A drained triaxial test was conducted on a saturated sand specimen using a stress-path triaxial testing system. The specimen failed when the axial stress reached a value of 100 kN/m2 from an initial confining pressure of 300 kN/m2.
The angle of shearing plane (in degrees) with respect to horizontal is _______ (rounded off to the nearest integer).- GATE CE - 2024
- Structural Engineering
- Working stress and Limit state design concepts
- A homogeneous, prismatic, linearly elastic steel bar fixed at both the ends has a slenderness ratio (l/r) of 105, where I is the bar length and r is the radius of gyration. The coefficient of thermal expansion of steel is 12 × 10-6 /°C. Consider the effective length of the steel bar as 0.51 and neglect the self-weight of the bar.
The differential increase in temperature (rounded off to the nearest integer) at which the bar buckles is- GATE CE - 2024
- Structural Engineering
- Working stress and Limit state design concepts
- The following figure shows a plot between shear stress and velocity gradient for materials/fluids P, Q, R, S, and T.
Which one of the following options is CORRECT?- GATE CE - 2024
- Structural Engineering
- Working stress and Limit state design concepts
- Various stresses in jointed plain concrete pavement with slab size of 3.5 m x 4.5 m are denoted as follows :
Wheel load stress at interior = \(S_{wl}^i\)
Wheel load stress at edge = \(S_{wl}^e\)
Wheel load stress at corner = \(S_{wl}^c\)
Warping stress at interior = \(S^i_t\)
Warping stress at edge = \(S_t^e\)
Warping stress at corner = \(S_t^c\)
Frictional stress between slab and supporting layer = \(S_f\)
The critical stress combination in the concrete slab during a summer midnight is- GATE CE - 2024
- Structural Engineering
- Working stress and Limit state design concepts
- Consider a balanced doubly-reinforced concrete section. If the material and other sectional properties remain unchanged, for which of the following cases will the section becomes under-reinforced?
- GATE CE - 2024
- Structural Engineering
- Working stress and Limit state design concepts
Questions Asked in GATE CE exam
- The three-dimensional state of stress at a point is given by
\(\sigma =\begin{pmatrix} 10 & 0 & 0\\ 0 & 40 & 0\\ 0 & 0 & 0 \end{pmatrix} \)
The maximum shear stress at the point is- GATE CE - 2024
- Matrix Algebra
- The in-situ percentage of voids of a sand deposit is 50%. The maximum and minimum densities of sand determined from the laboratory tests are 1.8 g/cm3 and 1.3 g/cm3, respectively. Assume the specific gravity of sand as 2.7.
The relative density index of the in-situ sand is ______ (rounded off to 2 decimal places).- GATE CE - 2024
- Principle of effective stress and quicksand condition
- The figure presents the trajectories of six vehicles within a time-space domain. The number in the parentheses represents unique identification of each vehicle.
- GATE CE - 2024
- Traffic studies on flow and speed
- Consider two matrices \(A=\begin{bmatrix} 2 & 1 & 4 \\ 1 & 0 & 3 \end{bmatrix}\) and \(B=\begin{bmatrix} -1 & 0 \\ 2 & 3 \\ 1 & 4 \end{bmatrix}\)
The determinant of the matrix AB is _____ (in integer).- GATE CE - 2024
- Matrix Algebra
- The magnetic bearing of a line in the year 1990 was found to be N 40°30' W and magnetic declination was 3°30′ E. If the present magnetic declination is 2°10′ W, the magnetic bearing now (in reduced bearing system) would be
View More Questions