Question:
The following figure shows a plot between shear stress and velocity gradient for materials/fluids P, Q, R, S, and T.
Which one of the following options is CORRECT?
The following figure shows a plot between shear stress and velocity gradient for materials/fluids P, Q, R, S, and T.
Which one of the following options is CORRECT?
Which one of the following options is CORRECT?
Updated On: Jul 18, 2024
- P→ Ideal Fluid; Q→ Ideal Bingham plastic
R→ Non-Newtonian fluid; S→ Newtonian fluid - P→ Real solid; Q → Ideal Bingham plastic
S→ Newtonian fluid; T→ Ideal Fluid - P→ Ideal Fluid; Q→ Ideal Bingham plastic
R→ Non-Newtonian fluid; T→ Real solid - P→ Real solid; Q → Newtonian fluid
R→ Ideal Bingham plastic; T → Ideal Fluid
Hide Solution
Verified By Collegedunia
The Correct Option is B
Solution and Explanation
The correct option is (B) : P→ Real solid; Q → Ideal Bingham plastic
S→ Newtonian fluid; T→ Ideal Fluid.
S→ Newtonian fluid; T→ Ideal Fluid.
Was this answer helpful?
0
0
Top Questions on Working stress and Limit state design concepts
- A drained triaxial test was conducted on a saturated sand specimen using a stress-path triaxial testing system. The specimen failed when the axial stress reached a value of 100 kN/m2 from an initial confining pressure of 300 kN/m2.
The angle of shearing plane (in degrees) with respect to horizontal is _______ (rounded off to the nearest integer).- GATE CE - 2024
- Structural Engineering
- Working stress and Limit state design concepts
- A homogeneous, prismatic, linearly elastic steel bar fixed at both the ends has a slenderness ratio (l/r) of 105, where I is the bar length and r is the radius of gyration. The coefficient of thermal expansion of steel is 12 × 10-6 /°C. Consider the effective length of the steel bar as 0.51 and neglect the self-weight of the bar.
The differential increase in temperature (rounded off to the nearest integer) at which the bar buckles is- GATE CE - 2024
- Structural Engineering
- Working stress and Limit state design concepts
- Various stresses in jointed plain concrete pavement with slab size of 3.5 m x 4.5 m are denoted as follows :
Wheel load stress at interior = \(S_{wl}^i\)
Wheel load stress at edge = \(S_{wl}^e\)
Wheel load stress at corner = \(S_{wl}^c\)
Warping stress at interior = \(S^i_t\)
Warping stress at edge = \(S_t^e\)
Warping stress at corner = \(S_t^c\)
Frictional stress between slab and supporting layer = \(S_f\)
The critical stress combination in the concrete slab during a summer midnight is- GATE CE - 2024
- Structural Engineering
- Working stress and Limit state design concepts
- The structural design method that DOES NOT take into account the safety factors on the design loads is
- GATE CE - 2024
- Structural Engineering
- Working stress and Limit state design concepts
- Consider a balanced doubly-reinforced concrete section. If the material and other sectional properties remain unchanged, for which of the following cases will the section becomes under-reinforced?
- GATE CE - 2024
- Structural Engineering
- Working stress and Limit state design concepts
Questions Asked in GATE CE exam
- The three-dimensional state of stress at a point is given by
\(\sigma =\begin{pmatrix} 10 & 0 & 0\\ 0 & 40 & 0\\ 0 & 0 & 0 \end{pmatrix} \)
The maximum shear stress at the point is- GATE CE - 2024
- Matrix Algebra
- The in-situ percentage of voids of a sand deposit is 50%. The maximum and minimum densities of sand determined from the laboratory tests are 1.8 g/cm3 and 1.3 g/cm3, respectively. Assume the specific gravity of sand as 2.7.
The relative density index of the in-situ sand is ______ (rounded off to 2 decimal places).- GATE CE - 2024
- Principle of effective stress and quicksand condition
- The figure presents the trajectories of six vehicles within a time-space domain. The number in the parentheses represents unique identification of each vehicle.
- GATE CE - 2024
- Traffic studies on flow and speed
- Consider two matrices \(A=\begin{bmatrix} 2 & 1 & 4 \\ 1 & 0 & 3 \end{bmatrix}\) and \(B=\begin{bmatrix} -1 & 0 \\ 2 & 3 \\ 1 & 4 \end{bmatrix}\)
The determinant of the matrix AB is _____ (in integer).- GATE CE - 2024
- Matrix Algebra
- The magnetic bearing of a line in the year 1990 was found to be N 40°30' W and magnetic declination was 3°30′ E. If the present magnetic declination is 2°10′ W, the magnetic bearing now (in reduced bearing system) would be
View More Questions