Question:
The phases present in pearlite are
The phases present in pearlite are
Updated On: Jul 9, 2024
- austenite and ferrite
- cementite and austenite
- ferrite and cementite
- martensite and ferrite
Hide Solution
Verified By Collegedunia
The Correct Option is C
Solution and Explanation
The correct option is (C): ferrite and cementite
Was this answer helpful?
0
0
Top Questions on Free-body diagrams and equilibrium
- A rigid massless tetrahedron is placed such that vertex O is at the origin and the other three vertices A, B, and C lie on the coordinate axes as shown in the figure. The body is acted on by three point loads, of which one is acting at A along x-axis and another at point B along y-axis. For the body to be in equilibrium, the third point load acting at point O must be
- GATE Metallurgy - 2024
- Applied Mechanics and Design
- Free-body diagrams and equilibrium
- A rigid beam AD of length $3a = 6$ m is hinged at A and supported by two strings as shown. A force $F = 9$ kN is applied at C. Assuming small deflection and linear elastic strings, the tension in the string at C is __________ kN (round off to 2 decimal places).
- GATE ME - 2022
- Applied Mechanics and Design
- Free-body diagrams and equilibrium
- A square plate is supported in four different ways (configurations (P) to (S) as shown in the figure). A couple moment $C$ is applied on the plate. Assume all the members to be rigid and mass-less, and all joints to be frictionless. All support links of the plate are identical. The square plate can remain in equilibrium in its initial state for which one or more of the following support configurations?
- GATE ME - 2022
- Applied Mechanics and Design
- Free-body diagrams and equilibrium
A block of negligible mass rests on a surface that is inclined at 30° to the horizontal plane as shown in the figure. When a vertical force of 900 N and a horizontal force of 750 N are applied, the block is just about to slide.
The coefficient of static friction between the block and surface is \(\underline{\hspace{2cm}}\) (round off to two decimal places).
- GATE ME - 2021
- Applied Mechanics and Design
- Free-body diagrams and equilibrium
Questions Asked in GATE Metallurgy exam
- At the instant when OP is vertical and AP is horizontal, the link OD is rotating counter clockwise at a constant rate w=7rad/s. Pin P on link OD slides in the slot BC of link ABC which is hinged at A, and causes a clockwise rotation of the link ABC. The magnitude of angular velocity of link ABC for this instant is _____rad/s (rounded off to 2 decimal places).
- GATE Metallurgy - 2024
- Principles of the design of machine elements such as bolted, riveted and welded joints
- In an arc welding process, the voltage and current are 30V and 200A, respectively. The cross-sectional area of the joint is 20 mm2 and the welding speed is 5mm/s. The heat required to melt the material is 20 J/s. The percentage of heat lost to the surrounding during the welding process is ____(rounded off to 2 decimal places).
- GATE Metallurgy - 2024
- Principles of welding, brazing, soldering and adhesive bonding
- Let f(z) be an analytic function, where z = x + iy. If the real part of f(z) is cosh x cos y, and the imaginary part of f(z) is zero for y = 0, then f(z) is
- GATE Metallurgy - 2024
- Analytic functions
- Steady, compressible flow of air takes place through an adiabatic converging- diverging nozzle, as shown in the figure. For a particular value of pressure difference across the nozzle, a stationary normal shock wave forms in the diverging section of the nozzle. If E and F denote the flow conditions just upstream and downstream of the normal shock, respectively, which of the following statement(s) is/are TRUE?
- GATE Metallurgy - 2024
- Basics of compressible fluid flow
- A set of jobs U, V, W, X, Y, Z arrive at time t = 0 to a production line consisting of two workstations in series. Each job must be processed by both workstations in sequence (i.e., the first followed by the second). The process times (in minutes) for each job on each workstation in the production line are given below.
Job U V W X Y Z Workstation 1 5 7 3 4 6 8 Workstation 2 4 6 6 8 5 7
The sequence in which the jobs must be processed by the production line if the total makespan of production is to be minimized is- GATE Metallurgy - 2024
- Principles of non-traditional machining processes
View More Questions