Question:
The number of junctions in the circuit is:
\includegraphics[width=0.5\linewidth]{13.png}
The number of junctions in the circuit is:
\includegraphics[width=0.5\linewidth]{13.png}
\includegraphics[width=0.5\linewidth]{13.png}
Show Hint
In electrical circuits, junctions are points where three or more components meet. Nodes and junctions are key in circuit analysis.
Updated On: Jan 23, 2025
- \(6\)
- \(7\)
- \(8\)
- \(9\)
Hide Solution
Verified By Collegedunia
The Correct Option is C
Solution and Explanation
Step 1: Identify junctions in the circuit where three or more elements meet.
Step 2: From the given circuit diagram, the total number of such junctions is \(6\).
Step 3: Count each unique point of connection carefully to avoid over-counting.
Step 2: From the given circuit diagram, the total number of such junctions is \(6\).
Step 3: Count each unique point of connection carefully to avoid over-counting.
Was this answer helpful?
0
0
Top Questions on Mathematical Logic
There are nine species of Impatiens (balsams) found in laterite plateaus of the northern Western Ghats, each with a distinct colour. If a plateau has exactly 6 species, then the number of possible colour combinations in the plateau is ….. (Answer in integer).
- GATE EY - 2024
- General Aptitude
- Mathematical Logic
- In linear regression, mean squared regression (effect variance) divided by mean squared error (error variance) is called the:
- GATE EY - 2024
- General Aptitude
- Mathematical Logic
- A researcher measures the heights of 200 randomly selected individuals of a tree species in a forest. Which one of the following is NOT a measure of variability in the sample?
- GATE EY - 2024
- General Aptitude
- Mathematical Logic
- The chart given below compares the Installed Capacity (MW) of four power generation technologies, T1, T2, T3, and T4, and their Electricity Generation (MWh) in a time of 1000 hours (h). The Capacity Factor of a power generation technology is: \[ \text{Capacity Factor} = \frac{\text{Electricity Generation (MWh)}}{\text{Installed Capacity (MW)} \times 1000 \, (h)} \] Which one of the given technologies has the highest Capacity Factor? \includegraphics[width=0.5\linewidth]{8.png}
- GATE EY - 2024
- General Aptitude
- Mathematical Logic
- On a given day, how many times will the second-hand and the minute-hand of a clock cross each other during the clock time 12:05:00 hours to 12:55:00 hours?
- GATE EY - 2024
- General Aptitude
- Mathematical Logic
View More Questions
Questions Asked in GATE EE exam
- A single-phase full bridge voltage source inverter (VSI) feeds a purely inductive load. The inverter output voltage is a square wave in \( 180^\circ \) conduction mode. The fundamental frequency of the output voltage is \( 50 \, \text{Hz} \). If the DC input voltage of the inverter is \( 100 \, \text{V} \) and the value of the load inductance is \( 20 \, \text{mH} \), the peak-to-peak load current in amperes is (rounded off to the nearest integer).
- A single-phase half-controlled bridge converter supplies an inductive load with ripple-free load current. The triggering angle of the converter is \( 60^\circ \). The ratio of the rms value of the fundamental component of the input current to the rms value of the total input current of the bridge is (rounded off to 3 decimal places).
- GATE EE - 2024
- Current
- A single-phase full-controlled thyristor converter bridge is used for regenerative braking of a separately excited DC motor with the following specifications: Rated armature voltage = \( 210 \, \text{V} \), Rated armature current = \( 10 \, \text{A} \), Rated speed = \( 1200 \, \text{rpm} \), Armature resistance = \( 1 \, \Omega \), Input to the converter bridge = \( 240 \, \text{V at 50 Hz} \). Assume that the motor is running at \( 600 \, \text{rpm} \) and the armature terminals of the motor are suitably reversed for regenerative braking. If the armature current of the motor is to be maintained at the rated value, the triggering angle of the converter bridge in degrees should be (rounded off to 2 decimal places).
\begin{tabular}{|l|l|} \hline Parameter & Value
\hline Rated armature voltage & 210 V
\hline Rated armature current & 10 A
\hline Rated speed & 1200 rpm
\hline Armature resistance & 1 $\Omega$
\hline Input to the converter bridge & 240 V at 50 Hz
\hline \end{tabular}
The armature of the DC motor is fed from the fullcontrolled bridge and the field current is kept constant.- GATE EE - 2024
- Current
- In the DC-DC converter shown in the figure, the current through the inductor is continuous. The switching frequency is \( 500 \, \text{Hz} \). The voltage (\( V_o \)) across the load is assumed to be constant and ripple-free. The peak inductor current in amperes is (rounded off to the nearest integer).
\includegraphics[width=0.5\linewidth]{64.png}- GATE EE - 2024
- Current
- A difference amplifier is shown in the figure. Assume the op-amp to be ideal. The CMRR (in dB) of the difference amplifier is (rounded off to 2 decimal places).
\includegraphics[width=0.5\linewidth]{61.png}- GATE EE - 2024
- Current
View More Questions