The effective resistance of a parallel connection that consists of four wires of equal length, equal area of cross-section, and same material is 0.25 Ω. What will be the effective resistance if they are connected in series?
The effective resistance of a parallel connection that consists of four wires of equal length, equal area of cross-section, and same material is 0.25 Ω. What will be the effective resistance if they are connected in series?
4 Ω
0.25 Ω
0.5 Ω
1 Ω
The Correct Option is A
Solution and Explanation
Top Questions on Current electricity
- In a meter bridge experiment to determine the value of unknown resistance, first the resistances \(2\,\Omega\) and \(3\,\Omega\) are connected in the left and right gaps of the bridge and the null point is obtained at a distance \(l\) cm from the left end. Now, when an unknown resistance \(x\,\Omega\) is connected in parallel to \(3\,\Omega\), the null point is shifted by \(10\,\text{cm}\) to the right. The value of \(x\) is ________ \(\Omega\).
- JEE Main - 2026
- Physics
- Current electricity
A Wheatstone bridge is initially at room temperature and all arms of the bridge have same value of resistances \[ (R_1=R_2=R_3=R_4). \] When \(R_3\) resistance is heated, its resistance value increases by \(10%\). The potential difference \((V_a-V_b)\) after \(R_3\) is heated is _______ V.
- JEE Main - 2026
- Physics
- Current electricity
The heat generated in 1 minute between points A and B in the given circuit, when a battery of 9 V with internal resistance of 1 \(\Omega\) is connected across these points is ______ J.
- JEE Main - 2026
- Physics
- Current electricity
The following diagram shows a Zener diode as a voltage regulator. The Zener diode is rated at \(V_z = 5\) V and the desired current in load is 5 mA. The unregulated voltage source can supply up to 25 V. Considering the Zener diode can withstand four times of the load current, the value of resistor \(R_s\) (shown in circuit) should be_______ \(\Omega\).
- JEE Main - 2026
- Physics
- Current electricity
An object is projected with kinetic energy K from point A at an angle 60° with the horizontal. The ratio of the difference in kinetic energies at points B and C to that at point A (see figure), in the absence of air friction is :
- JEE Main - 2026
- Physics
- Current electricity
Questions Asked in NEET exam
- Two cities X and Y are connected by a regular bus service with a bus leaving in either direction every T min. A girl is driving scooty with a speed of 60 km/h in the direction X to Y. She notices that a bus goes past her every 30 minutes in the direction of her motion, and every 10 minutes in the opposite direction. Choose the correct option for the period T of the bus service and the speed (assumed constant) of the buses.
- NEET (UG) - 2025
- Relative Velocity
- A physical quantity P is related to four observations a, b, c, and d as follows: P = a3 b2 (c / √d) The percentage errors of measurement in a, b, c, and d are 1%, 3%, 2%, and 4% respectively. The percentage error in the quantity P is:
- NEET (UG) - 2025
- Dimensional analysis and its applications
What is Microalbuminuria ?
- NEET (UG) - 2025
- Human physiology
The output (Y) of the given logic implementation is similar to the output of an/a …………. gate.
- NEET (UG) - 2025
- Logic gates
- An oxygen cylinder of volume 30 litre has 18.20 moles of oxygen. After some oxygen is withdrawn from the cylinder, its gauge pressure drops to 11 atmospheric pressure at temperature \(27^\circ\)C. The mass of the oxygen withdrawn from the cylinder is nearly equal to: [Given, \(R = \frac{100}{12} \text{ J mol}^{-1} \text{K}^{-1}\), and molecular mass of \(O_2 = 32 \text{ g/mol}\), 1 atm pressure = \(1.01 \times 10^5 \text{ N/m}^2\)]
- NEET (UG) - 2025
- Ideal-gas equation and absolute temperature
Concepts Used:
Resistance
Resistance is the measure of opposition applied by any object to the flow of electric current. A resistor is an electronic constituent that is used in the circuit with the purpose of offering that specific amount of resistance.
R=V/I
In this case,
v = Voltage across its ends
I = Current flowing through it
All materials resist current flow to some degree. They fall into one of two broad categories:
- Conductors: Materials that offer very little resistance where electrons can move easily. Examples: silver, copper, gold and aluminum.
- Insulators: Materials that present high resistance and restrict the flow of electrons. Examples: Rubber, paper, glass, wood and plastic.
Resistance measurements are normally taken to indicate the condition of a component or a circuit.
- The higher the resistance, the lower the current flow. If abnormally high, one possible cause (among many) could be damaged conductors due to burning or corrosion. All conductors give off some degree of heat, so overheating is an issue often associated with resistance.
- The lower the resistance, the higher the current flow. Possible causes: insulators damaged by moisture or overheating.