Question:
Match the following features with the corresponding symbols Feature in mine plan Symbol P shaft 1 
Q staple shaft 2 
R Abandoned shaft 3 
S Abandoned staple shaft 4 
Match the following features with the corresponding symbols
| Feature in mine plan | Symbol | ||
| P | shaft | 1 | |
| Q | staple shaft | 2 | |
| R | Abandoned shaft | 3 | |
| S | Abandoned staple shaft | 4 | |
Updated On: Jul 18, 2024
- P→1; Q→3; R→ 4; S→ 2
- P→ 4; Q → 2; R→ 1; S→ 3
- P→ 2; Q→ 4; R→ 3; S → 1
- P→4; Q→ 1; R→ 2; S→ 3
Hide Solution
Verified By Collegedunia
The Correct Option is D
Solution and Explanation
The correct option is (D): P→4; Q→ 1; R→ 2; S→ 3
Was this answer helpful?
0
0
Top Questions on Sampling: Methods, Practices and Interpretation
- The data obtained from an air sample analysis of an old working in a coal mine are given.
O2 17.15%, CO2 3.40%, CH4 2.20%, and N2 77.25%.
Considering atmospheric air contains
O2 20.95%, CO2 0.03%, and N2 79.02%,
the percentage of blackdamp in the old working, is____.( round off up to 2 decimals)- GATE MN - 2024
- Mine Planning
- Sampling: Methods, Practices and Interpretation
- The combined sound pressure level measured at a point in a production bench due to one dumper and one shovel is 95 dB(A). If the sound pressure level of shovel alone is 90 dB(A), the sound pressure level of the dumper alone, in dB(A), at the same point is_____.(round off up to 2 decimals)
- GATE MN - 2024
- Mine Planning
- Sampling: Methods, Practices and Interpretation
Questions Asked in GATE MN exam
- A longwall panel is to be developed in a flat seam at a depth of \( H \) m. The surface subsidence profile (\( s \)) of the area with the horizontal distance \( x \) is estimated as \[ s = \frac{S_{{max}}}{2} \left[ 1.002 - \tanh \left( \frac{4.8x}{H} \right) \right], \] where \( S_{{max}} \) is the maximum subsidence at the centre of the panel, \( x \) is measured from the inflection point. The value of \( x \) is negative towards the panel centre and positive towards the panel boundary. The ratio between the critical width of the panel and the depth is:
- GATE MN - 2025
- Mine planning and its components
An electricity utility company charges ₹7 per kWh. If a 40-watt desk light is left on for 10 hours each night for 180 days, what would be the cost of energy consumption? If the desk light is on for 2 more hours each night for the 180 days, what would be the percentage-increase in the cost of energy consumption?
- A direct rope haulage has the following details:
Output = 24 tonne/hour,
Length of trip = 610 m,
Gradient = 1 in 12,
Capacity of mine car = 1.0 tonne,
Tare weight of mine car = 0.5 tonne,
Average rope speed = 1.694 m/s,
Change over time of cars = 3 minutes,
Acceleration due to gravity = 10.0 m/s².
Neglecting all frictional resistance and mass of the rope, the minimum power required, in kW, to raise the loaded mine cars is:- GATE MN - 2025
- Mine planning and its components
- In a ventilation network, three airways with resistances of 4.0 Ns\( ^2 \)m\( ^{-8} \), 6.25 Ns\( ^2 \)m\( ^{-8} \) and 9.0 Ns\( ^2 \)m\( ^{-8} \) are connected in parallel.
The equivalent resistance of the network in Ns\( ^2 \)m\( ^{-8} \) is _________ (rounded off to 2 decimal places)}- GATE MN - 2025
- Mine planning and its components
- Consider a five-digit number PQRST that has distinct digits P, Q, R, S, and T, and satisfies the following conditions:
1. \( P<Q \)
2. \( S>P>T \)
3. \( R<T \)
If integers 1 through 5 are used to construct such a number, the value of P is:- GATE ST - 2025
- GATE CS - 2025
- GATE MN - 2025
- GATE XE - 2025
- GATE XL - 2025
- mathematical reasoning
View More Questions