Question:
Inductance is measured by
Inductance is measured by
Show Hint
Schering → capacitance, Kelvin → low resistance, Wien → frequency, Maxwell → inductance.
Updated On: Dec 29, 2025
- Schering bridge
- Maxwell bridge
- Kelvin bridge
- Wien bridge
Hide Solution
Verified By Collegedunia
The Correct Option is B
Solution and Explanation
A Schering bridge is used for measuring capacitance and dielectric loss.
A Kelvin bridge is used for measuring very low resistance.
A Wien bridge is mainly used for audio frequency measurement and determining frequency.
A Maxwell bridge, however, is specifically designed for accurate measurement of inductance using a known RC network for balance.
Thus, Maxwell bridge is the correct answer.
Final Answer: Maxwell bridge
A Kelvin bridge is used for measuring very low resistance.
A Wien bridge is mainly used for audio frequency measurement and determining frequency.
A Maxwell bridge, however, is specifically designed for accurate measurement of inductance using a known RC network for balance.
Thus, Maxwell bridge is the correct answer.
Final Answer: Maxwell bridge
Was this answer helpful?
0
0
Top Questions on Bridges and Potentiometers
The maximum percentage error in the equivalent resistance of two parallel connected resistors of 100 ohm and 900 ohm, with each having a maximum 5% error, is:
- GATE EE - 2025
- Electrical and Electronic Measurements
- Bridges and Potentiometers
- The induced EMF in a 3.3 kV, 4-pole, 3-phase, Y-connected synchronous motor is considered to be equal and in phase with the terminal voltage under no-load condition. On application of a mechanical load, the induced EMF phasor is deflected by an angle of 2 degrees with respect to the terminal voltage phasor. If the isochronous reactance is 2 ohms and the series resistance is negligible, the motor armature current magnitude, in amperes, during loaded condition, is closest to:
- GATE EE - 2025
- Electrical and Electronic Measurements
- Bridges and Potentiometers
- Four strain gauges $R_A, R_B, R_C, R_D$ (nominal $R$) are in a bridge. Under force: $R_A$ and $R_D$ increase by $\Delta R$, $R_B$ and $R_C$ decrease by $\Delta R$. A potentiometer of total resistance $R_v$ is connected as shown to rebalance the bridge. If $R=100~\Omega$ and $\Delta R=1~\Omega$, the minimum $R_v$ required to balance the bridge is _____ $\Omega$ (rounded off to two decimal places).
- GATE IN - 2023
- Electrical and Electronic Measurements
- Bridges and Potentiometers
- The bridge shown is balanced when \( R_1 = 100 \, \Omega \), \( R_2 = 210 \, \Omega \), \( C_2 = 2.9 \, \mu\text{F} \), and \( R_4 = 50 \, \Omega \). The 2 kHz sine-wave generator supplies a voltage of 10 V\(_\text{p-p}\). The value of \( L_3 \) (in millihenry) is _________ (round off to two decimal places)
- GATE IN - 2022
- Electrical and Electronics Measurements
- Bridges and Potentiometers
- In the Wheatstone bridge circuit shown, \( R_1 = 1.5 \, k\Omega \) and \( R_2 = R_3 = R_4 = 1 \, k\Omega \). The switch is initially open and the voltage between the points C and D is \( V_{CD} \). Upon closing the switch at \( t = 0 \), the resistance in the arm AD changes by an amount \( \delta R_1 \), and the voltage between C and D changes by \( \delta V_{CD} \). The sensitivity of the bridge in volt/kilohm, defined as \( \left| \frac{\delta V_{CD}}{\delta R_1} \right| \), is _________.
- GATE IN - 2022
- Electrical and Electronics Measurements
- Bridges and Potentiometers
View More Questions
Questions Asked in GATE EE exam
- The input voltage \( v(t) \) and current \( i(t) \) of a converter are given by, \[ v(t) = 300 \sin(\omega t) \, {V} \] \[ i(t) = 10 \sin\left(\omega t - \frac{\pi}{6}\right) + 2 \sin\left(3\omega t + \frac{\pi}{6}\right) + \sin\left(5\omega t + \frac{\pi}{2}\right) \, {A} \] where \( \omega = 2\pi \times 50 \) rad/s. The input power factor of the converter is closest to:
- A 3-phase, 400 V, 4 pole, 50 Hz star-connected induction motor has the following parameters referred to stator: \[ R'_1 = 1 \, \text{ohm}, \, X_s = X'_1 = 2 \, \text{ohm} \] Stator resistance, magnetizing reactance, and core loss of the motor are neglected. The motor is run with constant \( v/f \) control. The output frequency from the drive is closest to:
- GATE EE - 2025
- Transient and Steady‐state analysis of linear time invariant systems
In the Wheatstone bridge shown below, the sensitivity of the bridge in terms of change in balancing voltage \( E \) for unit change in the resistance \( R \), in V/Ω, is __________ (round off to two decimal places).
- GATE EE - 2025
- Electrical Energy, Power
- A DC series motor with negligible series resistance is running at a certain speed driving a load, where the load torque varies as the cube of the speed. The motor is fed from a 400 V DC source and draws 40 A armature current. Assume a linear magnetic circuit. The external resistance in ohms that must be connected in series with the armature to reduce the speed of the motor by half is closest to:
- GATE EE - 2025
- Instrument transformers
- Instrument(s) required to synchronize an alternator to the grid is/are:
- GATE EE - 2025
- Electrical Energy, Power
View More Questions