Question:
In a hydraulic system, the point of intersection of the line of action of the resultant hydrostatic force and the corresponding surface is known as:
In a hydraulic system, the point of intersection of the line of action of the resultant hydrostatic force and the corresponding surface is known as:
Show Hint
The center of pressure helps in understanding the distribution of hydrostatic forces on submerged surfaces, and it plays an important role in fluid mechanics.
Updated On: June 02, 2025
- Centre of pressure
- Centre of locust
- Centre of velocity
- Centre of momentum
Hide Solution
Verified By Collegedunia
The Correct Option is A
Solution and Explanation
The centre of pressure is the point where the resultant hydrostatic force acts on the surface of the body. This point is crucial in determining the stability of submerged bodies in fluids.
Was this answer helpful?
0
0
Top Questions on Fluid Mechanics
- The flow of an incompressible fluid is described by the Bernoulli equation. Which of the following quantities is not conserved along a streamline in steady flow?
- A rectangular slab consists of two cubes of copper and brass of equal sides having thermal conductivities in the ratio \(4 : 1\). If the free face of brass is at \(0^\circ \text{C}\) and that of copper is at \(100^\circ \text{C}\), then the temperature of their interface is
- AP EAPCET - 2025
- Physics
- Fluid Mechanics
- When the temperature increases, the viscosity of
- AP EAPCET - 2025
- Physics
- Fluid Mechanics
- A mercury drop of radius \( 1 \) cm is divided into \( 10^6 \) droplets of equal size. If the surface tension of mercury is \( 35 \times 10^{-3} \) N/m, then the change in surface energy in the process is:
- AP EAPCET - 2025
- Physics
- Fluid Mechanics
- An aeroplane of mass \( 4.5 \times 10^4 \) kg and total wing area of \( 600 \, \text{m}^2 \) is travelling at a constant height. The pressure difference between the upper and lower surfaces of its wings is (Acceleration due to gravity \( = 10 \, \text{m s}^{-2} \))
- AP EAPCET - 2025
- Physics
- Fluid Mechanics
View More Questions
Questions Asked in TANCET exam
- What letter replaces the question mark?
- An intermediate shaft of a gearbox, supporting two spur gears A and B and mounted between two bearings C1 and C2, is shown in the below figure. The pitch circle diameters of gears A and B are 500 and 250 mm respectively. The shaft is made of alloy steel 20MnCr5. (\( S_{ut} = 620 \) and \( S_{yt} = 480 \) N/mm\(^2\)). The factors \( k_b \) and \( k_t \) of the ASME code are 2 and 1.5 respectively. The gears are keyed to the shaft. Determine the shaft diameter using the ASME code.
- TANCET - 2024
- Machine Design
- A train moving at 108 km/hr crosses a platform in 30 seconds. Then it crosses a man running at 12 km/hr in the same direction in 9 seconds. What is the length of train and platform in m?
- TANCET - 2024
- Time, Speed and Distance
- The speed of a motor boat in still water is 7km/hr. If the speed of the motor boat against the stream is 5 km/hr, what is the speed of the stream?
- TANCET - 2024
- Time, Speed and Distance
A closed-loop system has the characteristic equation given by: $ s^3 + k s^2 + (k+2) s + 3 = 0 $.
For the system to be stable, the value of $ k $ is:- TANCET - 2024
- Microprocessors
View More Questions
