If the percentage error in measuring length and diameter of a wire is \(0.1\%\) each, then the percentage error of the resistance of the wire is :
- 0.3%
- 0.2%
- 0.1%
- 0.4%
The Correct Option is A
Solution and Explanation
The Correct Option is (A): \(0.3\%\)
\(R=\frac{pl}{A}\)
\(\frac{\triangle{R}}{R}=\frac{\triangle{l}}{l}+2\frac{\triangle{d}}{d}\)
=0.3%
Top Questions on Resistance
The graph between variation of resistance of a wire as a function of its diameter keeping other parameters like length and temperature constant is
- KCET - 2025
- Physics
- Resistance
- What is the resistance of a conductor if the potential difference across it is 12 V and the current flowing through it is 3 A?
- VITEEE - 2025
- Physics
- Resistance
A wire of resistance $ R $ is bent into a triangular pyramid as shown in the figure, with each segment having the same length. The resistance between points $ A $ and $ B $ is $ \frac{R}{n} $. The value of $ n $ is:
- JEE Main - 2025
- Physics
- Resistance
- A current of 2 A flows through a conductor with a resistance of 5 \(\Omega\). Calculate the potential difference across the conductor.
- MHT CET - 2025
- Physics
- Resistance
- Calculate the resultant resistance in the following circuit.
- TS POLYCET - 2024
- Physics
- Resistance
Questions Asked in JEE Main exam
- Consider the following cases of standard enthalpy of reaction (\( \Delta H_f^\circ \) in kJ mol\(^{-1}\)): \[ \text{C}_2\text{H}_6(g) + 7 \text{O}_2(g) \rightarrow 2 \text{CO}_2(g) + 3 \text{H}_2\text{O}(l) \quad \Delta H_1^\circ = -1550 \] \[ \text{C(graphite)} + \text{O}_2(g) \rightarrow \text{CO}_2(g) \quad \Delta H_2^\circ = -393.5 \] \[ \text{H}_2(g) + \frac{1}{2} \text{O}_2(g) \rightarrow \text{H}_2\text{O}(g) \quad \Delta H_3^\circ = -286 \] The magnitude of \( \Delta H_f^\circ \) of \( \text{C}_2\text{H}_6(g) \) is ____ kJ mol\(^{-1}\) (Nearest integer).
- JEE Main - 2025
- Hess’s law
- The complex of Ni\(^{2+}\) ion and dimethyl glyoxime contains ____ number of Hydrogen (H) atoms.
- JEE Main - 2025
- Coordination chemistry
- 20 mL of 2 M NaOH solution is added to 400 mL of 0.5 M NaOH solution. The final concentration of the solution is ___ x \( 10^{-2} \) M. (Nearest integer)
- JEE Main - 2025
- Dilution and Concentration Calculations
- If \( B \) is magnetic field and \( \mu_0 \) is permeability of free space, then the dimensions of \( \frac{B}{\mu_0} \) is:
- JEE Main - 2025
- Electromagnetic induction
- A solid sphere of mass \( m \) and radius \( r \) is allowed to roll without slipping from the highest point of an inclined plane of length \( L \) and makes an angle of \( 30^\circ \) with the horizontal. The speed of the particle at the bottom of the plane is \( v_1 \). If the angle of inclination is increased to \( 45^\circ \) while keeping \( L \) constant, the new speed of the sphere at the bottom of the plane is \( v_2 \). The ratio of \( v_1^2 : v_2^2 \) is:
- JEE Main - 2025
- Rotational Motion and Torque
Concepts Used:
Resistance
Resistance is the measure of opposition applied by any object to the flow of electric current. A resistor is an electronic constituent that is used in the circuit with the purpose of offering that specific amount of resistance.
R=V/I
In this case,
v = Voltage across its ends
I = Current flowing through it
All materials resist current flow to some degree. They fall into one of two broad categories:
- Conductors: Materials that offer very little resistance where electrons can move easily. Examples: silver, copper, gold and aluminum.
- Insulators: Materials that present high resistance and restrict the flow of electrons. Examples: Rubber, paper, glass, wood and plastic.
Resistance measurements are normally taken to indicate the condition of a component or a circuit.
- The higher the resistance, the lower the current flow. If abnormally high, one possible cause (among many) could be damaged conductors due to burning or corrosion. All conductors give off some degree of heat, so overheating is an issue often associated with resistance.
- The lower the resistance, the higher the current flow. Possible causes: insulators damaged by moisture or overheating.