For a fully developed flow through a pipe, the ratio of the maximum velocity to the average velocity is
Show Hint
- 1
- 2
- $\sqrt{2}$
- 4
The Correct Option is B
Solution and Explanation
Top Questions on Fluid Mechanics
- An oil of density \(870 \, {kg/m}^3\) and viscosity \(0.036 \, {Pa.s}\) flows through a straight pipe of 10 cm diameter and 1.5 km length at the flow rate of 250 liters per minute under the steady and incompressible flow conditions.
To control the flow rate of oil, a valve is fixed at the middle of the pipe causing no change in the total length of the pipe. The total head loss measured across the two ends of the pipe is \(11.60 \, {m}\). Using gravitational acceleration as \(10 \, {m/s}^2\), the minor head loss contributed by the presence of the valve in m {(rounded off to 2 decimal places) is ..........}- GATE XE - 2025
- Engineering Sciences
- Fluid Mechanics
A fixed control volume has four one-dimensional boundary sections (1, 2, 3, and 4). For a steady flow inside the control volume, the flow properties at each section are tabulated below:
The rate of change of energy of the system which occupies the control volume at this instant is \( E \times 10^6 \, {J/s} \). The value of \( E \) (rounded off to 2 decimal places) is ........- GATE XE - 2025
- Engineering Sciences
- Fluid Mechanics
A liquid flows under steady and incompressible flow conditions from station 1 to station 4 through pipe sections P, Q, R, and S as shown in the figure. Consider, \( d \), \( V \), and \( h \) represent the diameter, velocity, and head loss, respectively, in each pipe section with subscripts ‘P’, ‘Q’, ‘R’, and ‘S’. \( \Delta h \) represents the head difference between the inlet (station 1) and outlet (station 4). All the pipe sections are placed on the same horizontal plane for which the figure shows the top view.
(Insert diagram here, if possible)- GATE XE - 2025
- Engineering Sciences
- Fluid Mechanics
Figure shows the steady and incompressible flow of a fluid in the direction of the arrow from section A to section D. Three pipe connectors are to be placed between sections at A and D having Total Energy Line (TEL) and Hydraulic Grade Line (HGL) as depicted in the figure. Consider, \( g \), \( P \), \( Q \), \( V \), \( \gamma \), and \( Z \) denote gravitational acceleration, pressure, volume flow rate, velocity, specific weight, and elevation of the centerline of the pipe connectors from the datum, respectively. Which one of the following options, in sequence, indicates the correct nature of connectors between sections A and B, B and C, and C and D in the direction of flow?
- GATE XE - 2025
- Engineering Sciences
- Fluid Mechanics
- A solid body of uniform specific gravity floats in a deep liquid pool. Take \( B \), \( G \), and \( M \) as the centre of buoyancy, centre of gravity, and metacentre of the body, respectively. Which one of the following options is correct for the stable floatation of the body in the pool when the body is given a small tilt angle?
- GATE XE - 2025
- Engineering Sciences
- Fluid Mechanics
Questions Asked in TS PGECET exam
When the enable data input \( D = 1 \), select inputs \( S_1 = S_0 = 0 \) in the 1×4 Demultiplexer, then the outputs \( Y_0, Y_1, Y_2, Y_3 \) are
- TS PGECET - 2024
- Analog and Digital Electronics
- The frequency modulation of a 3-\(\phi\) sinusoidal pulse width modulation is an odd multiple of 3. Then the output line voltage contains
- TS PGECET - 2024
- Power Electronics
The \( Z \) parameter \( Z_{21} \) of the following circuit is
- TS PGECET - 2024
- Electric circuits and fields
The \( h \) parameters of the following circuit is
- TS PGECET - 2024
- Electric circuits and fields
For an input voltage \( v = 10 \sin 1000t \), the Thevenin's impedance at the terminals X and Y for the following circuit is
- TS PGECET - 2024
- Electric circuits and fields