Question:
A 3 m long, horizontal, rigid, uniform beam PQ has negligible mass. The beam is subjected to a 3 kN concentrated vertically downward force at 1 m from P, as shown in the figure. The beam is resting on vertical linear springs at the ends P and Q. For the spring at the end P, the spring constant Kp 100 kN/m.
If the beam DOES NOT rotate under the application of the force and displaces only vertically, the value of the spring constant KQ (in kN/m) for the spring at the end Q is
A 3 m long, horizontal, rigid, uniform beam PQ has negligible mass. The beam is subjected to a 3 kN concentrated vertically downward force at 1 m from P, as shown in the figure. The beam is resting on vertical linear springs at the ends P and Q. For the spring at the end P, the spring constant Kp 100 kN/m.
If the beam DOES NOT rotate under the application of the force and displaces only vertically, the value of the spring constant KQ (in kN/m) for the spring at the end Q is
If the beam DOES NOT rotate under the application of the force and displaces only vertically, the value of the spring constant KQ (in kN/m) for the spring at the end Q is
Updated On: Jul 18, 2024
- 150
- 100
- 50
- 200
Hide Solution
Verified By Collegedunia
The Correct Option is C
Solution and Explanation
The correct option is (C) : 50.
Was this answer helpful?
0
0
Top Questions on Analysis of beams
- For the 6 m long horizontal cantilever beam PQR shown in the figure, Q is the midpoint. Segment PQ of the beam has flexural rigidity EI = 2 × 105 kN.m2 whereas the segment QR has infinite flexural rigidity. Segment QR is subjected to uniformly, vertically downward load of 5 kN/m.
The magnitude of the vertical displacement (in mm) at point Q is ______ (rounded off to 3 decimal places).- GATE CE - 2024
- Structural Engineering
- Analysis of beams
- The horizontal beam PQRS shown in the figure has a fixed support at point P, an internal hinge at point Q, and a pin support at point R. A concentrated vertically downward load (V) of 10 kN can act at any point over the entire length of the beam.
The maximum magnitude of the moment reaction (in kN. m) that can act at the support P due to V is _______ (in integer).- GATE CE - 2024
- Structural Engineering
- Analysis of beams
- A linearly elastic beam of length 2l with flexural rigidity EI has negligible mass. A massless spring with a spring constant k and a rigid block of mass m are attached to the beam as shown in the figure.
The natural frequency of this system is- GATE CE - 2024
- Structural Engineering
- Analysis of beams
- For a thin-walled section shown in the figure, points P, Q, and R are located on the major bending axis X - X of the section. Point Q is located on the web whereas point S is located at the intersection of the web and the top flange of the section.
Qualitatively, the shear center of the section lies at- GATE CE - 2024
- Structural Engineering
- Analysis of beams
Questions Asked in GATE CE exam
- The three-dimensional state of stress at a point is given by
\(\sigma =\begin{pmatrix} 10 & 0 & 0\\ 0 & 40 & 0\\ 0 & 0 & 0 \end{pmatrix} \)
The maximum shear stress at the point is- GATE CE - 2024
- Matrix Algebra
- The in-situ percentage of voids of a sand deposit is 50%. The maximum and minimum densities of sand determined from the laboratory tests are 1.8 g/cm3 and 1.3 g/cm3, respectively. Assume the specific gravity of sand as 2.7.
The relative density index of the in-situ sand is ______ (rounded off to 2 decimal places).- GATE CE - 2024
- Principle of effective stress and quicksand condition
- The figure presents the trajectories of six vehicles within a time-space domain. The number in the parentheses represents unique identification of each vehicle.
- GATE CE - 2024
- Traffic studies on flow and speed
- Consider two matrices \(A=\begin{bmatrix} 2 & 1 & 4 \\ 1 & 0 & 3 \end{bmatrix}\) and \(B=\begin{bmatrix} -1 & 0 \\ 2 & 3 \\ 1 & 4 \end{bmatrix}\)
The determinant of the matrix AB is _____ (in integer).- GATE CE - 2024
- Matrix Algebra
- The magnetic bearing of a line in the year 1990 was found to be N 40°30' W and magnetic declination was 3°30′ E. If the present magnetic declination is 2°10′ W, the magnetic bearing now (in reduced bearing system) would be
View More Questions