List of top Engineering Graphics Questions asked in CUET (UG)

Read the passage and answer the following question

Rohan during his industrial visit saw a storage tank which is a combination of different solids he has studied in his class. for preparing his industrial visit report, he clicked pictures and measured dimensions of the tank and other machine parts in the industry. one such picture from his report is shown here (dimension given are in meters.) ihnor the thickness, stands, opening and branches of the tank and answer the following questions.

The given figure shows the disassembled part of a flange pipe joint. Answer the following question based on this drawing.

Raman is the student of Engineering Graphics. One day his younger brother was colouring his drawings. Raman noticed that all colour pencils are in the shape of the combination of solids like cone and cylinder. Then he write some questions related to this combination and asked to his friends as per given image.

A mechanic in an automobile workshop was fitting a number plate on a vehicle using rivets. The given figure shows the different types of rivets. Based on this knowledge, answer the following questions.

Identify the correct statements for the given figure :

(A) A triangular pyramid is resting on H.P. on its base.
(B) A triangular pyramid is resting on H.P. on its apex.
(C) Axis of pyramid is perpendicular to H.P.
(D) Axis of pyramid is parallel to H.P.
(E) Axis of pyramid is perpendicular to V.P.
Choose the correct answer from the options given below:
                                

 

Identify the correct statements for the Nut:
(A) Chamfering is done to save material.
(B) A circular disc having a non-threaded hole is nut.
(C) A prism having a threaded hole is nut.
(D) Thickness of nut is equal to nominal diameter of its bolt.
(E) Only octagonal nuts are used every where.
Choose the correct answer from the options given below :

Identify the correct statements for the types of projection:
(A) Axonometric projection is of three types.
(B) In dimetric projection, all the angles between principal axes are equal.
(C) In isometric projection, lines parallel to principal axes are known as isometric line.
(D) Perspective projection is a type of parallel projection.
(E)Orthographic projection is a single plane projection.
Choose the correct answer from the options given below:
                              

 

Identify the correct statements for the given figure :

(A) A hexagonal prism is resting on a pentagonal prism.
(B) A pentagonal pyramid is resting on a hexagonal prism.
(C) Common Axis is perpendicular to H.P.
(D) Common Axis is Parallel to H.P.
(E) A Pentagonal prism is resting on a hexagonal prism.
Choose the correct answer from the options given below:

 

Identify the correct statements for the Rivets :
(A) Rivets has threaded portion at one end.
(B) Rivets are called headless bolt.
(C) Rivets are permanent fasteners.
(D) Rivets are widely used in clay articles.
(E) Rivets are used in boilers.
Choose the correct answer from the options given below :

Identify the correct statements for the Gib and cotter joint:
(A) In gib and cotter joint two cotters are used. 
(B) Cotter is a permanent fastener.
(C) Usually taper ratio of cotter is taken as 1:30.
(D) The thickness of gib is same as that of cotter.
(E) Both gib and cotter have taper on their all edges. 
Choose the correct answer from the options given below: 

Identify the correct statements for given figure:

A) A cone is resting on H.P. on its apex.
B) A hexagonal prism is resting on H.P.
C) Common axis is perpendicular to H.P.
D) Prism has six rectangular faces.
E) A cone is resting on hexagonal pyramid.
Choose the correct answer from the options given below:

Identify the correct statements for given figure:

A) A triangular prism is resting on a circular slab.
B) Axis of triangular prism is perpendicular to V.P.
C) Axis of circular slab is parallel to H.P.
D) Axis of triangular prism is perpendicular to H.P.
E) Axis of circular slab is perpendicular to V.P.
Choose the correct answer from the options given below:

Choose the correct statement, according to the given figure:

Choose the incorrect statement for the given figure:

Choose the correct statement for the given figure:

Choose the correct statement for the given figure:

Choose the correct statement for the given figure:

Match List - I with List - II.

List - I (Assemblies)	List - II (No of parts used)
(A) Bush Bearing	(I) Three
(B) Gib and Cotter Joint	(II) Five
(C) Turnbuckle Joint	(III) Two
(D) Sleeve and Cotter Joint	(IV) Four

Choose the correct answer from the options given below:

Match List - I with List - II.

List - I (Machine parts of assembly)	List - II (Second name)
(A) Strap	(I) Hollow Cylinder
(B) Gasket	(II) Supporting device
(C) Bearing	(III) Fork
(D) Sleeve	(IV) Circular rubber packing

Choose the correct answer from the options given below:

Match List - I with List - II.

List - I (Machine Parts)	List - II (Their Features)
(A) Bolt	(I) A machine part having a threaded hole
(B) Nut	(II) A cylindrical piece having threads at both ends
(C) Washer	(III) A cylindrical body with one end threaded and other end in form of Head
(D) Stud	(IV) A circular plate having a hole in its centre

Choose the correct answer from the options given below:

Identify the correct statements regarding Isometric Scale.
A) True scale is marked on horizontal base line.
B) Isometric scale is marked on a line inclined at 45° with horizontal base line
C) Isometric scale is used to draw isometric view.
D) Isometric scale can measure the length of isometric lines
E) Isometric scale cannot measure the length of non-isometric lines.
Choose the correct answer from the options given below:

Match List - I with List- II.

List - I (Dimension in Isometric Projection)	List - II (Isometric length)(Approx)
(A) Long edge of the prism	(I) 16 mm
(B) Short edge of the prism	(II) 32 mm
(C) Radius of Cylinder	(III) 64 mm
(D) Diameter of Cylinder	(IV) 20 mm

Choose the correct answer from the options given below:

Match List - I with List - II.

List - I Types of Rivets	List - II Standard Dimensions (d-Rivet diameter)
(A) Snap Head Rivet	(I) Head Diameter = 2d
(B) Fiat Head Rivet	(II) Head Diameter = 16d
(C) Pan Head Rivet	(III) Radius of head = 0.8d
(D) CSK Head Rivet	(IV) Slant thickness of head = 0.5d

Choose the correct answer from the options given below:

Match List - I with List- II.

List - I (Types of Projection)	List - II (Uses)
(A) Perspective Projection	(I) Used to draw multiple views.
(B) Oblique Projection	(II) Used in mechanical engineering to show blocks and assemblies
(C) Isometric Projection	(III) Used by mathematicians and furniture manufactures.
(D) Orthographic Projection	(IV) Used by artists and designers

Choose the correct answer from the options given below:

Identify the correct statements for Sleeve and Cotter Joint.
A) This joint is used to connect two round rods.
B) In this joint gib is used with cotter.
C) This joint is used to join two rectangular rods.
D) Cotters are inserted in sleeve at right angle to axes of rods.
E) Taper of cotter is usually 1:40.

Choose the correct answer from the options given below: