Question:
The correct combination that relates the constructional feature, machine type and mitigation is \(\underline{\hspace{2cm}}\).
The correct combination that relates the constructional feature, machine type and mitigation is \(\underline{\hspace{2cm}}\).
Show Hint
Always match the feature with the machine that physically uses it, then identify the disturbance it mitigates.
Updated On: Dec 29, 2025
- P-V-X, Q-U-Z, R-T-Y
- P-U-X, Q-S-Y, R-V-Z
- P-T-Y, Q-V-Z, R-S-X
- P-U-X, Q-V-Y, R-T-Z
Hide Solution
Verified By Collegedunia
The Correct Option is B
Solution and Explanation
P = Damper bars → Synchronous machine → Hunting (X).
Q = Skewed rotor slots → Induction motor → Magnetic locking (Y).
R = Compensating winding → DC machine → Armature reaction (Z).
Thus the matching combination is option (B).
Final Answer: (B)
Q = Skewed rotor slots → Induction motor → Magnetic locking (Y).
R = Compensating winding → DC machine → Armature reaction (Z).
Thus the matching combination is option (B).
Final Answer: (B)
Was this answer helpful?
0
0
Top Questions on Electromechanical energy conversion principles
- The four stator conductors (A, A$'$, B and B$'$) of a rotating machine are carrying DC currents of the same value, the directions of which are shown in the figure (i). The rotor coils $a$–$a'$ and $b$–$b'$ are formed by connecting the back ends of conductors $a$ and $a'$, and $b$ and $b'$, respectively, as shown in figure (ii). The e.m.f. induced in coil $a$–$a'$ and coil $b$–$b'$ are denoted by $E_{a\text{–a'}$ and $E_{b\text{–}b'}$, respectively. If the rotor is rotated at uniform angular speed $\omega \, \text{rad/s}$ in the clockwise direction then which of the following correctly describes the $E_{a\text{–}a'}$ and $E_{b\text{–}b'}$?} \begin{center} \includegraphics[width=0.5\textwidth]{07.jpeg} \end{center}
- GATE EE - 2023
- Electrical Machines
- Electromechanical energy conversion principles
Questions Asked in GATE EE exam
- The input voltage \( v(t) \) and current \( i(t) \) of a converter are given by, \[ v(t) = 300 \sin(\omega t) \, {V} \] \[ i(t) = 10 \sin\left(\omega t - \frac{\pi}{6}\right) + 2 \sin\left(3\omega t + \frac{\pi}{6}\right) + \sin\left(5\omega t + \frac{\pi}{2}\right) \, {A} \] where \( \omega = 2\pi \times 50 \) rad/s. The input power factor of the converter is closest to:
- A 3-phase, 400 V, 4 pole, 50 Hz star-connected induction motor has the following parameters referred to stator: \[ R'_1 = 1 \, \text{ohm}, \, X_s = X'_1 = 2 \, \text{ohm} \] Stator resistance, magnetizing reactance, and core loss of the motor are neglected. The motor is run with constant \( v/f \) control. The output frequency from the drive is closest to:
- GATE EE - 2025
- Transient and Steady‐state analysis of linear time invariant systems
In the Wheatstone bridge shown below, the sensitivity of the bridge in terms of change in balancing voltage \( E \) for unit change in the resistance \( R \), in V/Ω, is __________ (round off to two decimal places).
- GATE EE - 2025
- Electrical Energy, Power
- A DC series motor with negligible series resistance is running at a certain speed driving a load, where the load torque varies as the cube of the speed. The motor is fed from a 400 V DC source and draws 40 A armature current. Assume a linear magnetic circuit. The external resistance in ohms that must be connected in series with the armature to reduce the speed of the motor by half is closest to:
- GATE EE - 2025
- Instrument transformers
- Instrument(s) required to synchronize an alternator to the grid is/are:
- GATE EE - 2025
- Electrical Energy, Power
View More Questions