Question:
Potential flow is the flow of
Potential flow is the flow of
Show Hint
Potential flow is an idealized case used in inviscid flow approximations.
Updated On: June 02, 2025
- Compressible fluids with shear
- Compressible fluids with no shear
- Incompressible fluids with shear
- Incompressible fluids with no shear
Hide Solution
Verified By Collegedunia
The Correct Option is D
Solution and Explanation
Potential flow assumes irrotational and incompressible conditions with no viscosity.
Thus, it excludes shear stress and rotational effects.
Thus, it excludes shear stress and rotational effects.
Was this answer helpful?
0
0
Top Questions on Fluid Mechanics
- In a water tank, an air bubble rises from the bottom to the top surface of the water. If the depth of the water in the tank is 7.28 m and atmospheric pressure is 10 m of water, then the ratio of the radii of the bubble at the bottom of the tank and at the top surface of the water is (Temperature of the water in the tank is constant)
- AP EAPCET - 2025
- Physics
- Fluid Mechanics
- A small solid sphere of mass 10 g and density \( 2600 \, \text{kg/m}^3 \) is dropped into a long vertical column of glycerine. When the sphere attains terminal velocity, the magnitude of the viscous force acting on the sphere is
(Acceleration due to gravity \( g = 10 \, \text{m/s}^2 \), Density of glycerine \( = 1300 \, \text{kg/m}^3 \))- AP EAPCET - 2025
- Physics
- Fluid Mechanics
- Water flows through a horizontal pipe with a velocity of 2 m/s. The cross-sectional area of the pipe reduces to half. What is the velocity of water in the narrower section?
- BITSAT - 2025
- Physics
- Fluid Mechanics
- An oil of density \(870 \, {kg/m}^3\) and viscosity \(0.036 \, {Pa.s}\) flows through a straight pipe of 10 cm diameter and 1.5 km length at the flow rate of 250 liters per minute under the steady and incompressible flow conditions.
To control the flow rate of oil, a valve is fixed at the middle of the pipe causing no change in the total length of the pipe. The total head loss measured across the two ends of the pipe is \(11.60 \, {m}\). Using gravitational acceleration as \(10 \, {m/s}^2\), the minor head loss contributed by the presence of the valve in m {(rounded off to 2 decimal places) is ..........}- GATE XE - 2025
- Engineering Sciences
- Fluid Mechanics
A fixed control volume has four one-dimensional boundary sections (1, 2, 3, and 4). For a steady flow inside the control volume, the flow properties at each section are tabulated below:
The rate of change of energy of the system which occupies the control volume at this instant is \( E \times 10^6 \, {J/s} \). The value of \( E \) (rounded off to 2 decimal places) is ........- GATE XE - 2025
- Engineering Sciences
- Fluid Mechanics
View More Questions
Questions Asked in TS PGECET exam
- Melting rates of electrodes in manual metal arc welding process is mainly governed by the
- TS PGECET - 2024
- Manufacturing Processes
- The maximum area of a rectangle that can be inscribed in a circle of radius $R$ is
- TS PGECET - 2024
- 3D Geometry
- For the matrix \[ \begin{bmatrix} 2 & 1 & 1 \\ 0 & 2 & 1 \\ 1 & 0 & 1 \end{bmatrix}, \] an Eigen vector among the following vectors is
- TS PGECET - 2024
- Linear Algebra
- Which of the following expression is a tautology?
- TS PGECET - 2024
- Digital Logic
- The 2’s complement representation of the decimal value $-15$ is
- TS PGECET - 2024
- Digital Logic
View More Questions
