Question:
Group I indicates type of spun yarns and group II indicates yarn characteristics. Match the yarns with their characteristics.
Group I indicates type of spun yarns and group II indicates yarn characteristics. Match the yarns with their characteristics.
Show Hint
For matching type questions in textile technology, focus on yarn structure and spinning technique. Knowing how yarns are spun helps match them with their resulting properties.
Updated On: Apr 28, 2025
- P-3, Q-1, R-2, S-4
- P-2, Q-3, R-4, S-1
- P-2, Q-3, R-1, S-4
- P-1, Q-2, R-3, S-4
Hide Solution
Verified By Collegedunia
The Correct Option is B
Solution and Explanation
Understanding each yarn type's characteristic.
Ring yarns: Known for strength and helical structure due to continuous twisting — matches with option 2.
Rotor yarns: Produced in open-end spinning; typically bulkier and have wrapper fibres — matches with option 3.
Friction yarns: Have very low fibre migration and are bulkier — matches with option 4.
Air-jet yarns: Have a nearly twistless core and are stiff — matches with option 1.
Ring yarns: Known for strength and helical structure due to continuous twisting — matches with option 2.
Rotor yarns: Produced in open-end spinning; typically bulkier and have wrapper fibres — matches with option 3.
Friction yarns: Have very low fibre migration and are bulkier — matches with option 4.
Air-jet yarns: Have a nearly twistless core and are stiff — matches with option 1.
Was this answer helpful?
0
0
Top Questions on Yarn Manufacture, Structure and Properties
- The breaking strain of a yarn is 1.5. If the stress (\( \sigma \)) and the strain (\( \epsilon \)) of the yarn are related as, \( \sigma = 1.5 \epsilon^2 \), then the work factor of the yarn (rounded off to 2 decimal places) is:
- GATE TF - 2025
- Textile Engineering and Fibre Science
- Yarn Manufacture, Structure and Properties
- The twist in a 36 Ne cotton yarn is 15 tpi. The twist multiplier (TM) in cotton system of the yarn (correct to 1 decimal place) is _________.
- GATE TF - 2025
- Textile Engineering and Fibre Science
- Yarn Manufacture, Structure and Properties
- A woven fabric has weft yarn of 24 tex and pick density of 25 per cm. It is desired to replace only the weft with a 6 tex yarn of the same packing density. The pick density per cm required to keep the fabric cover the same (answer in integer) is _________.
- GATE TF - 2025
- Textile Engineering and Fibre Science
- Yarn Manufacture, Structure and Properties
- The parameter(s) required to convert load-elongation curve to stress-strain curve of a yarn is/are:
- GATE TF - 2025
- Textile Engineering and Fibre Science
- Yarn Manufacture, Structure and Properties
- Cone winding machines equipped with electronic yarn clearers remove the following defect(s) from the spun yarn:
- GATE TF - 2025
- Textile Engineering and Fibre Science
- Yarn Manufacture, Structure and Properties
View More Questions
Questions Asked in GATE TF exam
- If \[ \begin{bmatrix} 2 \\ -1 \\ 1 \end{bmatrix} \quad \text{is the eigenvector of the matrix} \quad A = \begin{bmatrix} 8 & 11 & 3 \\ 4 & -1 & 3 \\ -4 & 10 & 6 \end{bmatrix}, \quad \text{then the corresponding eigenvalue is:} \]
- GATE TF - 2025
- Linear Algebra
- The solution of the following differential equation represents \[ \frac{dy}{dx} = \frac{y + 1}{x} \]
- GATE TF - 2025
- Differential Equations
- For crease resist finishing of cotton, 70 gpl aqueous solution of DMDHEU (molecular weight - 178) is applied by padding. If the DMDHEU is available as 50% (w/v) aqueous solution, then the required amount of DMDHEU solution (ml) for preparation of 1000 ml padding liquor is:
- GATE TF - 2025
- Textile Fibres and its Classification
- In a projectile weaving machine, the projectile travels through the shed at an average speed of 24 m/s taking \( \frac{2}{3} \) of the loom cycle. If the efficiency of the weaving machine is 90%, the weft insertion rate (m/min) is:
- GATE TF - 2025
- Weaving
- A needlepunching machine has two needle boards which operate sequentially at the same frequency to produce nonwoven with 200 punches/cm\(^2\). Each needle board has 40000 needles per meter width. If the delivery speed of the machine is 80 m/min, then the frequency (strokes/min) of each needle board is:
- GATE TF - 2025
- Textile Fibres and its Classification
View More Questions