Question:
A steel wire of $1\, m$ long and $1\, mm^2$ cross section area is hanged from rigid end when weight of $1 \,kg$ is hung from it then change in length will be (for wire Youngs coefficient $ Y=2\times 10^{11}\,N/m^{2} $ ):
A steel wire of $1\, m$ long and $1\, mm^2$ cross section area is hanged from rigid end when weight of $1 \,kg$ is hung from it then change in length will be (for wire Youngs coefficient $ Y=2\times 10^{11}\,N/m^{2} $ ):
Updated On: Jul 28, 2022
- 0.5 mm
- 0.25 mm
- 0.05 mm
- 5 mm
Hide Solution
Verified By Collegedunia
The Correct Option is C
Solution and Explanation
Young's coefficient of elasticity
$Y=\frac{m g L}{\pi r^{2} \Delta L}$
substituting the values we get
$\Delta L=0.05 \,mm$
Was this answer helpful?
0
0
Top Questions on mechanical properties of solids
- Match List-I with List-II :
List-I List-II (A) A force that restores an elastic body of unit area to its original state (I) Bulk modulus (B) Two equal and opposite forces parallel to opposite faces (IV) Shear modulus (C) Forces perpendicular everywhere to the surface per unit area same everywhere (III) Stress (D) Two equal and opposite forces perpendicular to opposite faces (II) Young's modulus
Choose the correct answer from the options given below :- JEE Main - 2024
- Physics
- mechanical properties of solids
- A plane electromagnetic wave of frequency 35 MHz travels in free space along the X-direction. At a particular point (in space and time), \( \vec{E} = 9.6 \hat{j} \, \text{V/m} \). The value of the magnetic field at this point is:
- JEE Main - 2024
- Physics
- mechanical properties of solids
- A wire of length L and radius r is clamped at one end. If its other end is pulled by a force F, its length increases by l. If the radius of the wire and the applied force both are reduced to half of their original values keeping original length constant, the increase in length will become.
- JEE Main - 2024
- Physics
- mechanical properties of solids
- Each of three blocks \( P \), \( Q \), and \( R \) shown in the figure has a mass of 3 kg. Each of the wires \( A \) and \( B \) has a cross-sectional area of 0.005 cm\(^2\) and Young's modulus \( 2 \times 10^{11} \, \text{N} \, \text{m}^{-2} \). Neglecting friction, the longitudinal strain on wire \( B \) is \( \ldots \times 10^{-4} \). (Take \( g = 10 \, \text{m/s}^2 \))
- JEE Main - 2024
- Physics
- mechanical properties of solids
- Two metallic wires \( P \) and \( Q \) have the same volume and are made of the same material. If their areas of cross-section are in the ratio \( 4 : 1 \) and a force \( F_1 \) is applied to \( P \), producing an extension of \( \Delta l \), the force required to produce the same extension in \( Q \) is \( F_2 \).The value of \( \frac{F_1}{F_2} \) is _______.
- JEE Main - 2024
- Physics
- mechanical properties of solids
View More Questions
Questions Asked in Rajasthan PMT exam
- 300 cal of heat is supplied to raise the temperature of 50 g of air from $ 20{}^\circ C $ to $ 30{}^\circ C $ without any change in its volume. Change in internal energy per gram of air is
- Rajasthan PMT - 2011
- internal energy
- The velocity of water flowing in a non-uniform tube is 20 cm/s at a point where the tube radius is 0.2 cm. The velocity at another point, where the radius is 0.1 cm, is
- Rajasthan PMT - 2011
- mechanical properties of fluid
- Block A of mass 4 kg and block B of mass 6 kg are resting on a horizontal surface as shown in the figure. There is no friction between the block B and the horizontal surface. The coefficient of friction between the blocks is 0.2. If the value of $ g=10\,m/{{s}^{2}}, $ the maximum horizontal force F that can be applied on block B without any relative motion between A and B is
- The excess pressure inside a soap bubble A is twice that in another soap bubble B. The ratio of volumes of A and B is
- Rajasthan PMT - 2011
- Surface tension
- The unit of surface tension is
- Rajasthan PMT - 2011
- Surface tension
View More Questions
Concepts Used:
Mechanical Properties of Solids
Mechanical properties of solids intricate the characteristics such as the resistance to deformation and their strength. Strength is the ability of an object to resist the applied stress, to what extent can it bear the stress.
Therefore, some of the mechanical properties of solids involve:
- Elasticity: When an object is stretched, it changes its shape and when we leave, it retrieves its shape. Or we can say it is the property of retrieving the original shape once the external force is removed. For example Spring
- Plasticity: When an object changes its shape and never attains its original shape even when an external force is removed. It is the permanent deformation property. For example Plastic materials.
- Ductility: When an object is been pulled in thin sheets, wires or plates, it will be assumed that it has ductile properties. It is the property of drawing into thin wires/sheets/plates. For example Gold or Silver
- Strength: The ability to hold out applied stress without failure. Many types of objects have higher strength than others.