Question:
A ballistic type impact tester is shown below. The test specimen is connected to the bob of the pendulum of 10 N weight. The pendulum is released from a height of 1 m from the base, and this results in rupture of test specimen. Considering no frictional losses and neglecting the weight of the connecting rod, if the work of rupture of the specimen is 10 N-m, then the total swing angle (degree) that the pendulum makes during its travel (in integer) is
A ballistic type impact tester is shown below. The test specimen is connected to the bob of the pendulum of 10 N weight. The pendulum is released from a height of 1 m from the base, and this results in rupture of test specimen. Considering no frictional losses and neglecting the weight of the connecting rod, if the work of rupture of the specimen is 10 N-m, then the total swing angle (degree) that the pendulum makes during its travel (in integer) is
Updated On: Jul 20, 2024
Hide Solution
Verified By Collegedunia
Correct Answer: 90
Solution and Explanation
The correct Answe is: 90 or 90 Approx
Was this answer helpful?
0
0
Top Questions on Yarn Manufacture, Structure and Properties
- A winder operates at 750 m/min with 93% efficiency. The time (in minutes) taken for the winder to wind 1.2 kg of 20 tex yarn is approximately _______.
- GATE TF - 2024
- Textile Engineering and Fibre Science
- Yarn Manufacture, Structure and Properties
- A parallel fibre strand of 30 tex count is coming out from the nip of the front delivery rollers of a ring spinning machine. This strand is given twist to produce a yarn such that the length of the yarn becomes 0.95 times the length of the parallel fibre strand. If 600 turns are present in 1 m length of the yarn, then the twist factor (tpm-tex0.5) of the yarn (rounded off to the nearest integer) is____
- GATE TF - 2024
- Textile Engineering and Fibre Science
- Yarn Manufacture, Structure and Properties
- Amongst the given options, the condition(s) which will increase the equilibrium wicking height of water in a yarn is/are
- GATE TF - 2024
- Textile Engineering and Fibre Science
- Yarn Manufacture, Structure and Properties
- Group I lists yarn manufacturing technologies and Group II contains typical structural features of the yarns. Match the manufacturing technology with the structural features of the yarn.
Group I Group II P. Rotor spinning 1. Twistless parallel fibres in core and helically arranged filament on surface Q. Air-jet spinning 2. Helically twisted core and distinct wrappers on surface R. Wrap spinning 3. Multifilament core covered by staple fibres stuck to molten polymer S. Bobtex spinning 4. Twistless core wrapped regularly and helically by thin fibre ribbons - GATE TF - 2024
- Textile Engineering and Fibre Science
- Yarn Manufacture, Structure and Properties
- A cotton yarn of 20 tex count is replaced by a polyester yarn such that both the yarns have the same diameter and the same packing density. Assuming densities of cotton and polyester fibres as 1.52 g/cm\(^3\) and 1.38 g/cm\(^3\), respectively, the count (tex) of the polyester yarn (rounded off to 2 decimal places) is ________________.
- GATE TF - 2024
- Textile Engineering and Fibre Science
- Yarn Manufacture, Structure and Properties
View More Questions
Questions Asked in GATE TF exam
- The value of the integral \( \int_{0}^{\infty} \frac{dx}{e^x + e^{-x}} \) is:
- GATE TF - 2024
- Definite and indefinite integrals
- Poly(ethylene terephthalate) has a number average molecular weight of 25000. The degree of polymerisation (rounded off to the nearest integer) is ____
- GATE TF - 2024
- Polymerization methods
- The approximate value of the integral \( \int_{2}^{3} \frac{dx}{x} \) using Simpson's rule with \( h = 0.5 \) is
- GATE TF - 2024
- Definite and indefinite integrals
- A circular weft knitting machine with 24 inch gauge and 20 inch diameter needle bed is used to make a tubular knitted fabric. If the fabric shrinks by 35% in course- wise direction upon withdrawal from the machine, the circumference (inch) of the shrunk tubular fabric is approximately
- GATE TF - 2024
- Principles of warp knitting
- As the package builds up in a roving frame, the component(s) whose speed DOES NOT remain constant, amongst the following, is/are
- GATE TF - 2024
- Principles of bobbin building in roving formation
View More Questions